Watkiss Automation BookMaster Скачать руководство пользователя страница 105

Страница: 105 / 128

Installation

•

BookMaster Receiving Tray (BRT)

Watkiss BookMaster Service Manual - Issue 1 - 04/12/00

Figure 7:5 BookMaster location pegs and interface socket

Figure 7:6 TrimMaster location pegs and interface socket

5. Connect the outfeed conveyor plug to the socket on the BookMaster or

TrimMaster.

7.4 BookMaster Receiving Tray (BRT)

The BookMaster Receiving Tray fits only on the BookMaster, not the Trim-
Master.

Procedure

1. Fit the back plate of the receiving tray onto the location pegs on the Book-

Master (see Figure 7:5). The angle can be adjusted by moving the slide up
and down.

2. Fit the platform of the receiving tray into one of three pairs of location slots

in the back plate.

All settings are variable to suit individual job requirements.

interface socket

location pegs

Outfeed conveyor

Interface socket

Waste conveyor

Location pegs

Содержание BookMaster

































































































































Результаты поиска

Содержание BookMaster

Отзывы:

Похожие инструкции для BookMaster

Бренды по названию

Популярные бренды

Watkiss Automation BookMaster, Руководство по обслуживанию

Результаты поиска

Содержание BookMaster

Отзывы:

Похожие инструкции для BookMaster

Бренды по названию

Популярные бренды