WaterLogic WL400 Series страница 65 Скачать руководство пользователя

Страница: 65 / 84

WL400

Manual Page 65

–

Revision: 10-23-2019

POWER TROUBLESHOOTING INDEX

1. Red Power Switch, Green Heater and Compressor Switch and the LEDs on the Front

won't light

2. Red Power Switch, Green Heater and Compressor Switch are lit but the red LED on the

Front is not lit

3. Compressor Runs but does Not Chill

4. Compressor is Not Running

Red Power Switch, Green Heater and Compressor Switch and the LEDs on the
Front won't light

Possible Reason

Solution

Circuit Breaker

Check the Circuit Breaker

Fuse is Blown

Replace Fuse

Defective / Loose Power Cord

Check that power cord is properly plugged in. If it is properly
plugged in, use a different power cord to verify.

Failed Power Socket with,
ElectroMagnetic Interference
Filter (EMI)

Replace Power Socket with, ElectroMagnetic Interference Filter
(EMI)

Defective Red Power Switch

Replace Red Power Switch

Defective Green Heater and
Compressor Switch

Replace Green Heater and Compressor Switch

Содержание WL400 Series





















































































Результаты поиска

Содержание WL400 Series

Отзывы:

Похожие инструкции для WL400 Series

Бренды по названию

Популярные бренды

WaterLogic WL400 Series, Руководство пользователя

Результаты поиска

Содержание WL400 Series

Отзывы:

Похожие инструкции для WL400 Series

Бренды по названию

Популярные бренды