background image

4

   

Warner Electric • 800-825-9050

P-2105-WE    819-0549    5/17

Mounting

Enclosed Units

Any vertical, horizontal, or angled surface is  
suitable for mounting the CBC-300 and CBC-300-1 .

Follow these procedures to mount your control .

q

  1 . Remove the front cover by removing the top and 

bottom retaining screws .

q

  2 . Set the control on the mounting surface and mark 

for the three mountings holes in accordance with 
“Dimensions .” (See Figure 1)

q

  3 . Install the top two mounting bolts or screws until 

they are nearly flush, set the control over the larger 
top mounting holes and pull down to position the 
control .

q

  4 . Tighten the top bolts or screws and install the 

bottom bolt or screw and tighten .

This completes the mounting of the control . The control 
is now ready for final wiring . Refer to the wiring section 
for final wiring .

q

  1 . If the CBC-300-1 control is used, first pre-wire 

the external potentiometers . Refer to: External 
Potentiometer wiring for CBC-300-1, page 5

q

  2 . If the CBC-300 control is used, refer to: Final 

Wiring, page 6

SHORT

POWER

WARNER ELECTRIC

CLUTCH-BRAKE

CURRENT CONTROL

CBC-300-1

SHORT

POWER

WARNER ELECTRIC

CLUTCH-BRAKE

CURRENT CONTROL

CHANNEL 1

TORQUE ADJUSTMENT

CBC-300

1

2

3

4

5

6

7

8

9

10

0

CBC-300-1

CBC-300

4.460

(113.3) Max.

6.500

(165.1)

Max.

2.250

(57.2)

1.095

(27.81)

0.620

(15.75)

5.185

(131.7)

2.220

(56.39)

Ø0.180

(4.57)

Mounting

Ø0.375

(9.53)

(2 Plcs)

Ø0.180

(4.57) Slot

Mounting 2 Plcs

2.500

(63.5)

Max.

1.812

(46.02)

Max.

2.062

(52.4)

Max.

CHANNEL 2

1

2

3

4

5

6

7

8

9

10

0

(Figure 1)

Содержание CBC-300 Series











Отзывы: