WarmFlow WAH 100 Скачать руководство пользователя страница 31

Страница: 31 / 32

Users Name: ....................................................................................................................................

Address of Installation: .....................................................................................................................

..........................................................................................................................................................

.................................................................... Postcode: ....................................................................

Tel No (Home): ....................................................... (Daytime): .......................................................

Heater Date Code: ...........................................................................................................................

Installation Date: ..............................................................................................................................

Heater Serial No: ..............................................................................................................................

Commissioned by: ............................................................................................................................

OFTEC No: ......................................................................................................................................

Address: ...........................................................................................................................................

.................................................................... Postcode: ....................................................................

Pump Pressure: ...............................................................................................................................

Co2 %: .............................................................................................................................................

FGT

C: ............................................................ Smoke No: ............................................................

Motor Current: .............................. Cold: .............................. Amps Hot: .............................. Amps

Date Commissioned: ........................................................................................................................

It is the responsibility of the installer to ensure that the heater is properly commissioned
(Ref BS 5410 Parts 1 & 2)

Failure to have this appliance commissioned may invalidate the warranty.

COMMISSIONING DETAILS

To ensure the reliable and efficient operation of your heater it is necessary to have this

appliance properly commissioned by a suitably qualified commissioning engineer. The page

below is to be completed by the commissioning engineer and the manual retained by the

end user.

Содержание WAH 100

































Результаты поиска

Содержание WAH 100

Отзывы:

Бренды по названию

Популярные бренды

WarmFlow WAH 100, Руководство по установке и обслуживанию

Результаты поиска

Содержание WAH 100

Отзывы:

Бренды по названию

Популярные бренды