W&H 20210492060001 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 23

background image

UNPACKING INSTRUCTIONS

Remove clear packaging.
Inspect the machine for any shipping damage.
Remove the side covers.
Cut the zip-tie around the motor.
Remove the motor shipping boards.
Remove the lag bolts holding the machine to the pallet.
Lift the machine off of the pallet.
Re-install the sides.
Before elevating the molder, loosen the motor lock.

Side panel Zip

‐

Tie Lag bolts

Motor shipping boards

Motor lock

«
...
2
3
4
5
6
...
»

Содержание 20210492060001
























Отзывы:

Нет отзывов

Похожие инструкции для 20210492060001

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Rangevision Страницы: 28

Бренд: T-Rex Страницы: 13

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: R.M. Young Страницы: 10

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Omlet Страницы: 60

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: Harken Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды