WAGO 750-494 Series Скачать руководство пользователя страница 52

Страница: 52 / 134

Process Image

WAGO-I/O-SYSTEM 750

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Collections for harmonics analysis (020, 021, 022)

The corresponding harmonics analysis collection is selected in the I/O module

output data and the MET_IDs set. These measured values are then made available

in the input data.

The type of measured value is selected in the harmonics analysis collections using

the corresponding MET_ID_1. The following types of measured data are

available:

MET_ID_1 = 001 :

RMS value current for fundamental component or

harmonic

MET_ID_1 = 002 :

RMS value voltage for fundamental component or

harmonic

MET_ID_1 = 003 :

THD (Total Harmonic Distortion) for fundamental

component or HD (Harmonic Distortion) for current

harmonic

MET_ID_1 = 004 :

THD for fundamental component or HD for

voltage harmonic

MET_ID_2, MET_ID_3 and MET_ID_4 are then used to select the harmonic

(MET_ID_x = 1 ... 40) or fundamental component (MET_ID_x = 100) for the

measured values defined by MET_ID_1 are to be made available in the process

image input data. This means that 3 measured values are provided with the input

data.

Example 1:

Byte Output data

Input data

0 0x00

0x48

1 0x03 (Status query)

0x00

2 0x00

0x40

3 0x14 (COL_ID)

0x14 (COL_ID_SEL)

4 0x02 (MET_ID_1)

0x02 (MET_ID_1_SEL)

5 0x64 (MET_ID_2)

0x64 (MET_ID_2_SEL)

6 0x01 (MET_ID_3)

0x01 (MET_ID_3_SEL)

7 0x02 (MET_ID_4)

0x02 (MET_ID_4_SEL)

8 ---

Measured value type Ueff - [7:0] = 0x02

---

Measured value type Ueff - [15:8] = 0x00

---

Measured value type Ueff - [23:16] = 0x00

---

Measured value type Ueff - [31:24] = 0x00

---

Ueff – Fundamental component L1 [7:0]

---

Ueff – Fundamental component L1 [15:8]

---

Ueff – Fundamental component L1 [23:16]

---

Ueff – Fundamental component L1 [31:24]

---

Ueff – 1st harmonic L1 [7:0]

Содержание 750-494 Series







































































































































Результаты поиска

Содержание 750-494 Series

Отзывы:

Похожие инструкции для 750-494 Series

Бренды по названию

Популярные бренды

WAGO 750-494 Series, Руководство пользователя

Результаты поиска

Содержание 750-494 Series

Отзывы:

Похожие инструкции для 750-494 Series

Бренды по названию

Популярные бренды