WAGO 750-494 Series Скачать руководство пользователя страница 108

Страница: 108 / 134

108 Appendix

WAGO-I/O-SYSTEM 750

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Table 25: Register 5

Register 5 – Command interface response

Function

Data type

Access

Factory setting

Command Interface Response

UINT

[R]

0x0000

High byte

Sequence number (Session ID)

Low byte

Response
Request A mirror image of the request command is created when the command is successfully

applied.

0xF0

Command is valid, but cannot be executed.

0xFD

The session ID received by the master does not correspond to the last confirmed

session ID + 1.

0xFE

The command received by the master is not implemented in the slave.

0xFF

General internal error

Table 26: Register 32

Register 32 – Feature register

Function

Data type

Access

Factory setting

Feature Register

Flags

R/W

0x0000

Bit 0: -Reserved-
Bit 1: DC measurement

DC filter is active. (factory setting)

The DC filter will be bypassed.

Bit 2: Activation of the RUN LED/Watchdog Timer

The green RUN LED "A" lights up when data are transferred over the internal bus. This

LED is deactivated after a period of inactivity of 200 ms (factory setting).

The green RUN LED "A" remains lit.

Bit 3: Selection of nominal frequency

The nominal frequency is 50 Hz (factory setting).

The nominal frequency is 60 Hz.

Bit 4 + 5: -Reserved-
Bit 6 + 7: Phase selection for peak measurement

Peak measurement for phase L1 is active (factory setting).

Peak measurement for phase L2 is active.

Peak measurement for phase L3 is active.

-reserved-

Bit 8: Activation of automatic reset of min/max values for phase L1

Automatic deleting of minimum and maximum current, voltage and power values is not

activated (factory settings).

Automatic deleting of minimum and maximum current, voltage and power values is

activated.

Bit 9: Activation of automatic reset of min/max values for phase L2

Automatic deleting of minimum and maximum current, voltage and power values is not

activated (factory settings).

Automatic deleting of minimum and maximum current, voltage and power values is

activated.

Bit 10: Activation of automatic reset of min/max values for phase L3

Automatic deleting of minimum and maximum current, voltage and power values is not

activated (factory settings).

Содержание 750-494 Series







































































































































Результаты поиска

Содержание 750-494 Series

Отзывы:

Похожие инструкции для 750-494 Series

Бренды по названию

Популярные бренды

WAGO 750-494 Series, Руководство пользователя

Результаты поиска

Содержание 750-494 Series

Отзывы:

Похожие инструкции для 750-494 Series

Бренды по названию

Популярные бренды