WAGO 2789-9023 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 94

background image

2789-9023

Safety

10

Product manual | Version: 1.0.0
EtherNet/IP Communication Module

2

Safety

2.1 General Safety Rules

• This documentation is part of the product. Therefore, retain the documentation during

the entire service life of the product. Pass on the documentation to any subsequent
user of the product. In addition, ensure that any supplement to this documentation is
included, if necessary.

• The product must only be installed and put into operation by qualified electrical special-

ists per EN 50110‑1/-2 and IEC 60364.

• Comply with the laws, standards, guidelines, local regulations and accepted technol-

ogy standards and practices applicable at the time of installation.

2.2 Electrical Safety

• Make sure the product does not carry any voltage before starting work.

Grounding/Protection/Fuses

• When handling the product, please ensure that environmental factors (personnel, work

space and packaging) are properly equalized. Do not touch any conducting parts.

Cables

• Use shielded cables with copper braiding or tinned copper braiding. This reduces elec-

tromagnetic interference and increases signal quality. Measurement errors, data trans-
mission errors and interference due to excessive voltage can be prevented.

• Maintain spacing between control, signal and data lines and the power supply lines.
• Observe permissible temperature range of connecting cables.
• Use appropriate strain relief.

2.3 Mechanical Safety

• As the installer of the system, you are responsible for ensuring the necessary touch-

proof protection. Follow the installation guidelines for the specific application.

• Before startup, please check the product for any damage that may have occurred dur-

ing shipping. Do not put the product into operation in the event of mechanical damage.

• Do not open the product housing.
• The product is an open-type device and is designed for installation in an additional en-

closure, which supplies the following safety aspects:

– Restrict access to authorized personnel and may only be opened with tools.
– Ensure the required pollution degree in the vicinity of the system.
– Offer adequate protection against direct or indirect contact.
– Offer adequate protection against UV irradiation.
– Prevent fire from spreading outside of the enclosure.
– Guarantee mechanical stability.

«
...
8
9
10
11
12
...
»

Содержание 2789-9023































































































Отзывы:

Нет отзывов

Похожие инструкции для 2789-9023

Бренд: Haier Страницы: 58

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: TCS Страницы: 16

Бренд: Watlow Страницы: 4

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

Бренд: Waterway Страницы: 8

Бренд: Technische Alternative Страницы: 68

Бренд: Nautronic Страницы: 6

Бренд: Redbusbar Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды