WACKER Group PT 6LT Скачать руководство пользователя страница 52

Страница: 52 / 66

Maintenance

PT 6 /...

wc_tx000567gb.fm

5.28 Basic Troubleshooting

Problem / Symptom

Reason / Remedy

Engine does not start.

•

Fuel tank empty.

•

Wrong type of fuel.

•

Old fuel. Drain tank, change fuel filter, and fill with
fresh fuel.

•

Fuel system not primed.

•

Battery connections loose or corroded. Battery
dead. Electrolyte low.

•

Engine oil level low.

•

Engine hot.

•

Ignition switch defective.

•

Throttle solenoid defective.

•

Electrical connections loose or broken.

•

Engine faulty.

Engine is hard to start.

•

Dirt or debris inside pump housing blocking move-
ment of impeller.

•

Battery charge low.

•

Engine faulty.

Engine starts but pump does

not take in water.

•

Pump housing not filled with water.

•

Strainer on suction hose plugged.

•

Suction hose damaged. Air leak above water line.

•

Air leak at suction port.

•

Pump too high above water line.

•

Engine speed too low.

•

Debris collecting in pump housing.

Pump takes in water but little

or no discharge.

•

Suction strainer partially plugged.

•

Impeller worn. Shim insert.

•

Discharge hose kinked or blocked.

•

Engine speed too low.

Engines stops by itself.

•

No fuel.

•

Engine oil pressure low.

•

Engine too hot.

Содержание PT 6LT



































































Результаты поиска

Содержание PT 6LT

Отзывы:

Похожие инструкции для PT 6LT

Бренды по названию

Популярные бренды

WACKER Group PT 6LT, Руководство оператора

Результаты поиска

Содержание PT 6LT

Отзывы:

Похожие инструкции для PT 6LT

Бренды по названию

Популярные бренды