WACKER Group PT 6LT Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 66

background image

Maintenance

PT 6 /...

wc_tx000567gb.fm

42

5.18 Tires

Keep the tires properly inflated and make sure they have the proper
load rating. Under-inflated tires may cause a blowout which could
result in fishtailing or loss of control of the towing vehicle.

Always maintain full air pressure as indicated by the tire manufacturer
on the tire's sidewalls. Check air pressure when the tires are cold,
before you move the trailer. When the trailer tires become worn or
damaged, replace them promptly with the same type, size, and load
capacity as the original tires.

For convenience and safety, it is recommended that you carry a spare
wheel and tire.

5.19 Wheels and Lug Nuts

Loose or missing lug nuts can cause you to lose a wheel! Keep all lug
nuts tight.

Before each trip, check for loose or missing lug nuts. When replacing
lug nuts, make sure the replacement nut matches the original nut
exactly. While the threads of the nut may match, the nut may be a size
that does not hold the wheel securely against the hub even when fully
tightened. Torque nuts evenly in increments to 115 Nm (85 ft.lbs.).

Note:

During normal use, the lug nuts will seat during the first one

hundred miles resulting in a drop in torque. Each nut should be
checked at that time and torqued to the proper value.

5.20 Tongue Jack

See Graphic: wc_gr003181

All trailers are equipped with a tongue jack

(d)

. Use the tongue jack to

lift and lower the trailer coupling on or off the tow vehicle hitch.

WARNING

WARNING

«
...
42
43
44
45
46
...
»

Содержание PT 6LT



































































Отзывы:

Нет отзывов

Похожие инструкции для PT 6LT

Бренд: Danfoss Страницы: 8

Бренд: Danner Страницы: 2

Бренд: SAER Elettropompe Страницы: 76

Бренд: Watson Marlow Pumps Страницы: 95

Бренд: Watson Marlow Pumps Страницы: 87

Бренд: Watson Marlow Pumps Страницы: 127

Бренд: ubbink Страницы: 31

Бренд: A.O. Smith Страницы: 2

Residential Gas Water Heaters

Бренд: A.O. Smith Страницы: 84

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: Gardner Denver Страницы: 27

Бренд: alkitronic Страницы: 12

Бренд: Bryant Страницы: 4

Pond Clear 5000

Бренд: SuperFish Страницы: 12

Бренд: salmson Страницы: 68

Бренд: Naked Страницы: 12

Бренд: Wacker Neuson Страницы: 64

969-9365 Series

Бренд: Varian Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды