manualshive.com logo in svg

WACKER Group PT 6LT, Руководство оператора

Поделиться
Скачать
WACKER Group PT 6LT Скачать руководство пользователя страница 31

PT 6 /...

Maintenance

wc_tx000567gb.fm

29

5.3

Periodic Maintenance Schedule

The chart below lists basic engine maintenance. Refer to the engine
manufacturer’s Operation Manual for additional information on engine
maintenance.

* Change more often in dusty conditions. Refer to engine manufacturer’s manual.

Lombardini 11LD625-3 Engine

Daily

before 

starting

Every

125

hrs.

Every

250

hrs.

Every

500

 hrs.

Check engine oil. Fill to correct level.

„

Clean air cleaner.

„

Check condition and tension on fan belt.

„

Change oil in engine crankcase.*

„

Change engine oil filter.

„

Change fuel filter

„

Clean engine cooling fins.

„

Check valve clearance.

„

Tighten fittings and clean injectors

„

Replace fan belt.

„

Machine

Daily

before 

starting

Every

100

hrs.

Every

250

 hrs.

Every

500

hrs.

Check external hardware.

„

Open pump housing cover and remove any 
debris from inside of pump housing.

„

Check oil level in seal housing.   Fill to cor-
rect level.

„

Check bearing/seal housing for oil or water 
leaks.

„

Check oil level in bearing housing.

„

Drain water from water separator in fuel line.

„

Change oil in seal housing. 

„

Change oil in bearing housing.

„

Check coupling bolt tightness.

„

Содержание PT 6LT



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды