WACKER Group PT 6LT Скачать руководство пользователя страница 33

Страница: 33 / 66

PT 6 /...

Maintenance

wc_tx000567gb.fm

5.5

Fuel Filter

See Graphic: wc_gr001188

Change the engine fuel filter every 250 hours of operation.

5.5.1

Remove the filter

(a)

from the engine block.

5.5.2

Install a new filter. If necessary, prime the fuel lines as described in the
next section.

5.6

Priming the Fuel System

See Graphic: wc_gr00317

If the fuel tank has been run completely dry, it will be necessary to
prime the fuel system.

To prime fuel system:

5.6.1

Remove the small plug from the top of the water separator and prefill
the element with clean diesel fuel.

5.6.2

Loosen the bleed screw

(a)

on the fuel filter and pump the manual lever

on the fuel pump

(b)

until fuel flows freely from the screw hole. Tighten

the bleed screw.

5.6.3

Loosen the bleed screw

(c)

, starting with the injector closest to the fuel

filter, and manually pump until fuel flows freely from the screw hole.
Tighten the bleed screw. Repeat for each injector.

wc_gr001188

wc_gr003175

Содержание PT 6LT



































































Результаты поиска

Содержание PT 6LT

Отзывы:

Похожие инструкции для PT 6LT

Бренды по названию

Популярные бренды

WACKER Group PT 6LT, Руководство оператора

Результаты поиска

Содержание PT 6LT

Отзывы:

Похожие инструкции для PT 6LT

Бренды по названию

Популярные бренды