manualshive.com logo in svg

WACKER Group PT 6LT, Руководство оператора, Страница: 6 / 66

Поделиться
Скачать
WACKER Group PT 6LT Скачать руководство пользователя страница 6

Safety Information

PT 6 /...

wc_si000098gb.fm

4

2.

Safety Information

This manual contains DANGER, WARNING, CAUTION, 

NOTICE 

and

NOTE callouts which must be followed to reduce the possibility of
personal injury, damage to the equipment, or improper service. 

This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.

NOTICE

: Used without the safety alert symbol, 

NOTICE

 indicates a

hazardous situation which, if not avoided, could result in property
damage

Note:

  

Contains additional information important to a procedure

.

2.1

State Regulations Concerning Trailers

Trailer laws covering such things as brakes, lights, safety chains, etc.,
will vary from state to state. Make certain that your trailer is in
compliance with the regulations of the state in which the trailer will be
used. If you are not sure what these regulations are, contact the state
motor vehicle department for information.

In some states, trailers must be registered and licensed by the State
Department of Transportation. Before towing, be sure to check
licensing requirements.

DANGER

WARNING

CAUTION

Содержание PT 6LT



































































Отзывы:

Нет отзывов