manualshive.com logo in svg

Wachs FF 424, Руководство пользователя, Страница: 8 / 70

Поделиться
Скачать
Wachs FF 424 Скачать руководство пользователя страница 8

SDB 412 and FF 424

6

Part No. 66-MAN-01, Rev. A

E.H. Wachs

Always turn machine off before doing any adjustments 
or service.

•

SECURE LOOSE CLOTHING AND JEWELRY.

 

Secure or remove loose-fitting clothing and jewelry, and 
securely bind long hair, to prevent them from getting 
caught in moving parts of the machine. 

•

KEEP WORK AREA CLEAR.

 Keep all clutter and 

nonessential materials out of the work area. Only people 
directly involved with the work being performed should 
have access to the area.

Safety Symbols

This icon is displayed with any safety alert that indicates a 
personal injury hazard.

  

WARNING

This safety alert indicates a potentially hazardous situation 
that, if not avoided, 

could

 result in 

death or serious injury

.

  

CAUTION

This safety alert, with the personal injury hazard symbol, 
indicates a potentially hazardous situation that, if not 
avoided, 

could

 result in 

minor or moderate injury

.

Содержание FF 424







































































Отзывы:

Нет отзывов