manualshive.com logo in svg

Wachs FF 424, Руководство пользователя, Страница: 61 / 70

Поделиться
Скачать
Wachs FF 424 Скачать руководство пользователя страница 61

Parts Lists and Drawings: 

E.H. Wachs

Part No. 66-MAN-01, Rev. A

61

Fitting Mandrel (66-414-01)

26

25

29

7

30

8

27

20

28

6

16

2

34

1

18

15

13

19

24

23

21

14

22

REQUIRED FOR SETUP ONLY

17

3.75

 REF

95.3

"A"

"A"

DIMENSIONS IN BRACKETS ARE MILLIMETERS

ITEM

PART NUMBER

 QTY. 

DESCRIPTION

1

56-025-00

1

NUT, DRAWBAR

2

56-035-00

1

LOCKNUT, BEARING

3

56-036-00

1

WASHER, TONGUED

4

66-024-00

1

COLLAR, DRAWBAR NUT

5

66-075-00

1

BODY, CHUCK

6

66-079-00

1

SCREW, ADJUSTABLE

7

66-090-00

1

ADAPTER, 8.5" - 12.8" ELBOW MANDREL

8

66-096-00

1

SCREW, 1" DIA. ADJUSTABLE

9

66-097-00

1

BLOCK, LEG STORAGE (NOT SHOWN)

10

66-098-00

1

BLOCK, LEG STORAGE (NOT SHOWN)

11

66-099-00

1

LABEL, LEG RANGE (NOT SHOWN)

12

66-099-01

1

LABEL, LEG RANGE (NOT SHOWN)

13

66-125-00

1

PLATE, FACE

14

66-126-00

1

COLLAR

15

66-127-00

3

LEG

16

66-135-00

1

MANDREL

17

66-186-00

1

DRAW ROD ASSEMBLY

18

90-054-08

9

SSS,  1/4-20 X 7/8

19

90-055-53

3

WASHER, 1/4 FLAT

20

90-059-18

3

PLUNGER, 1/4-20 x 1/2 HVY-SPRNG BALL

21

90-059-28

2

SSS, 1/4-20 X 3/4 BRASS TIP

22

90-060-20

6

SHCS, 5/16-18 X 2

23

90-062-14

3

BHCS- 5/16-18 X 3/4

24

90-066-07

3

PIN, 5/16 X 3/4 DOWEL

25

90-069-05

3

PLUNGER, 5/16-18 X 1/2 BALL

26

90-090-57

3

SHCS, 1/2-20 X 1-3/4

27

WHERE USED

A/R

LEG

28

WHERE USED

A/R

LEG, ADJUSTABLE

29

WHERE USED

A/R

LEG, 1" DIA.

30

WHERE USED

A/R

LEG, 1" DIA. ADJUSTABLE

BODY, CHUCK DIA.

66-078-07

8.49 [215.6]

7.69 [195.3]

66-077-07

3

66-077-06

3.75 [95.3]

4.39 [111.6]

5.05 [128.3]

5.71 [145.0]

6.37 [161.8]

7.03 [178.5]

MIN.

6.51 [165.3]

7.83 [198.8]

5.19 [131.8]

MAX.

5.85 [148.6]

4.53 [115.1]

7.17 [182.1]

DIMENSION "A" DIA.

----

LEG, ADJUSTABLE

DESCRIPTION

QTY.

1

---

PART NO.

28

ITEM

DESCRIPTION

LEG

LEG

66-078-02

66-078-03

66-078-04

66-078-05

66-078-06

66-077-03

PART NO.

2

66-077-01

27

QTY.

66-077-05

66-077-04

ITEM

66-077-02

-WHERE USED-

30

66-093-05

1

66-094-02

29

66-094-01

66-094-04

LEG, 1"

66-093-04

66-093-02

66-094-06

66-093-06

66-093-01

LEG, 1" DIA. ADJUSTABLE

66-094-03

2

66-093-03

66-094-05

9.93 [252.2]

10.57 [268.5]

11.37 [288.8]

9.13 [231.9]

10.65 [270.5]

12.81 [325.3]

9.21 [233.9]

11.29 [286.8]

12.01 [305.1]

9.85 [250.2]

12.09 [307.1]

8.41 [213.7]

Содержание FF 424







































































Отзывы:

Нет отзывов