Wachs FF 424 Скачать руководство пользователя страница 22

Страница: 22 / 70

SDB 412/2 SMALL DIAMETER BEVELER

* T-15 HSS

coated

carbide

• A Tungsten type high speed steel, very high hardness, recommended for difficult to

machine materials

• A layer of Titanium Nitride to increase cutting life and performance

• Super-hard composite steel material offering maximum edge strength

N/A = Not Applicable

= Available

NOTICE:

Effective June 1995. Single piece tool bits shown on this page

have been replaced by holder and insert combinations and are

now available only by special order. contract manufacturer for

pricing and availability.

NOTE:

Tool bit ranges listed are to be used as guides when performing simultaneous prepping.

Individual tool usage will expand the cutting range.

TOOL BELT

CUTTING RANGE

T15*

HSS*

COATED*

TYPE

PART

NUMBER

DESCRIPTION

MAXIMUM

WALL

FACING

37.5

BEVELING

37.5

BEVELING

I. D. Deburring

J Bevel

Small 4:1 Taper
counterbore

Med 4:1 Taper
counterbore

Large 4:1 Taper
counterbore

56-701-01

56-700-02

56-702-01

56-702-02

56-703-00

56-704-00

56-705-01

56-705-02

56-705-03

see note

For low range O. D.

pipe or tube

For high range O. D.

pipe or tube

For high range O. D.

pipe or tube

For low range O. D.

pipe or tube

For low range O. D.

pipe or tube

For mid range O. D.

pipe or tube

For high range O. D.

pipe or tube

For high range O. D.

pipe or tube

For low range O. D.

pipe or tube

For mid range O. D.

pipe or tube

For high range O. D.

pipe or tube

1.50’ (38.1 mm)

N/A

1.50’ (38.1 mm)

I. D. Deburring

56-702-03

For low range O. D.

pipe or tube

N/A

Содержание FF 424







































































Результаты поиска

Содержание FF 424

Отзывы:

Wachs FF 424, Руководство пользователя, Страница: 22 / 70

Результаты поиска

Содержание FF 424

Отзывы: