Wachs FF 424 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 70

Wachs FF 424 Скачать руководство пользователя страница 7

Chapter 2, Safety

E.H. Wachs

Part No. 66-MAN-01, Rev. A

5

Safety

E.H. Wachs takes great pride in designing and manufactur-
ing safe, high-quality products. We make user safety a top
priority in the design of all our products.

Read this chapter carefully before operating the SDB 412/
FF 424. It contains important safety instructions and rec-
ommendations.

O

PERATOR

S

AFETY

Follow these guidelines for safe operation of the equip-
ment.

Look for this sym-

bol throughout the
manual. It indicates
a personal injury
hazard.

•

READ THE OPERATING MANUAL.

Make sure

you understand all setup and operating instructions
before you begin.

•

INSPECT MACHINE AND ACCESSORIES.

Before starting the machine, look for loose bolts or
nuts, leaking lubricant, rusted components, and any
other physical conditions that may affect operation.
Properly maintaining the machine can greatly decrease
the chances for injury.

•

ALWAYS READ PLACARDS AND LABELS.

Make

sure all placards, labels, and stickers are clearly legible
and in good condition. You can purchase replacement
labels from E.H. Wachs.

•

KEEP CLEAR OF MOVING PARTS.

Keep hands,

arms, and fingers clear of all rotating or moving parts.

In This Chapter

O

PERATOR

S

AFETY

S

AFETY

L

ABELS

«
...
5
6
7
8
9
...
»

Содержание FF 424







































































Отзывы:

Нет отзывов