manualshive.com logo in svg

Wachs FF 424, Руководство пользователя, Страница: 17 / 70

Поделиться
Скачать
Wachs FF 424 Скачать руководство пользователя страница 17

SDB 412/2 SMALL DIAMETER BEVELER

BEVELING MACHINE TO FLANGE FACER CONVERSION PROCEDURE

4. Mount flange facing tool slide on macrune

rotating head. Align dowel pin holes in flange

facer with the dowel pins on the machine head.

(FIG. 3)

NOTE: Be sure to install the felt washer. Coat  the

washer  with a light amount of oil in the rear

of the flange facing module.

1. Remove the mandrel from the machine  body.

Next, loosen and remove the four 3/8-16 x 1-1/4”

shcs securing the rotating tool holder plate

(Fig. 1).

2. Remove the rotating tool holder plate, (part # 66-

005-00) from the machine body by lifting it from

the two dowel pins pressed into the rotating

head. (Fig. 2)

Fig. 1

Fig. 2

3. Install the trip collar assembly onto the machine

housing by tightening the six locking socket set

screws located on the out diameter of the collar

assembly (Fig. 2).

NOTE: When installing the trip ring assembly, center

the cut out relief on trip ring over the air motor

housing for proper trip lever location. Be sure

that ring sits flush against housing all around.

Fig. 3

5. Secure with four 3/8-16 x 1-1/4” shcs.

Fig. 4

15

Содержание FF 424







































































Отзывы:

Нет отзывов