Series S34 Instruction Manual
Chapter 6 Troubleshooting and Repair
M-000-00030
6-5
•
Factory Defaults
= Reset factory defaults. If you change this to Yes and press Enter,
all the factory configuration is lost and you must reconfigure the entire program.
Consult the factory before performing this process, it is required only in very rare
cases.
•
Config Code =
Factory use only.
•
Test Pulse Out
= Force totalizer pulse. Set to Yes and press enter to send one pulse.
Very useful when needing to test totalizer counting equipment.
•
Test Scaled Freq
= Enter a frequency value in order to test the scaled frequency
output. Return to 0 to stop the test.
•
A2D Ref. Resistor =
Factory use only.
•
RTD1.
Press the RIGHT ARROW to access:
•
Ro
= RTD resistance at 0°C (1000 ohms).
•
A
= RTD coefficient A
•
B
= RTD coefficient B
•
RTD1 Max Deg. F =
356
•
RTD1 Min Deg. F =
-40
•
RTD2
= Second RTD configuration, for special applications only.
•
Correction Pairs
•
Frequency
(1 through 10)
•
Velocity
(1 through 10)
•
Absolute (Abs) Roughness in.
= Factory use only.
•
Force Recal?
= Factory use only.
•
Erase FRAM?
= Factory use only.
•
Min. Delta H =
Energy EMS meters only. Sets the deadband for totalization to begin.
Must be greater than this number (1 default) to initiate the totalizer.
•
Logging =
Defines the parameters associated with internal data logging.
•
Log Interval Sec
= The time, in seconds, determining when the unit records
the variables defined in the following four submenus.
•
Log Variable 1
= The first variable to be recorded during a logging session.
•
Log Variable 2
= The second variable to be recorded during a logging session.
•
Log Variable 3
= The third variable to be recorded during a logging session.
•
Log Variable 4
= The fourth variable to be recorded during a logging session.
•
Cutoff V ft/s
= The minimum velocity of an application before the software filters off
any value below this set value.
•
Slow Smoothing
= Slow time constant if smoothing is enabled in the
Display
Menu
under the
Display Smooth?
Submenu.
•
Fast Smoothing
= Fast time constant if smoothing is enabled in the
Display
Menu
under the
Display Smooth?
submenu.
Содержание SonoPro S34 Series
