manualshive.com logo in svg

Vorsis AirAura, Руководство пользователя

Поделиться
Скачать
Vorsis AirAura Скачать руководство пользователя страница 33

Hardware IP Address 

– This is the address of AirAura’s DSP farm and is the 

address that the remote GUI on a host computer will use to connect to AirAura 
and control it over the network. 

 
Subnet Mask 

– The subnet mask entry must be appropriate for the network 

being used. Please see your local IT person if this item is a bit confusing or 
consult one of the free online resources such as 

http://www.subnetmask.info/

 or 

http://www.subnet-calculator.com/

. 

 

Gateway 

– This is the gateway address that AirAura will use to reach 

connections 

outside

 of its own internal network. If you are on a local LAN 

segment or connected to AirAura by a direct connection, the Gateway address is 
not usually necessary and can be set to 0.0.0.0 or 255.255.255.255. 
 
After determining the IP address that you wish AirAura to use, enter that address 
in AirAura’s Hardware IP address field using the navigation buttons. It is a good 
idea to clear the entire IP address field before entering new data to ensure there 
will be no hard to see leading or training blanks in the address. 
 

AirAura’s Front Panel Network Settings 

Next, using the same sequence as above enter a new GUI IP address by adding 
“1” to the IP address that you entered for the hardware in the above step. 
 

Example: 

If you entered 192.168.0.200 as the hardware address, then the logically correct 
GUI address will be 192.168.0.201. Note that the front panel GUI address is 

not 

utilized externally by AirAura, however no other device on the connected network 
should be using this address – in other words this address must be 

reserved

 

even though it is not externally used. 
 
Enter the correct Subnet Mask and Gateway in the same manner as the IP 
addresses were entered. Then click the “OK” box. When prompted to reboot 
AirAura for the changes to take effect, click “OK” and then interrupt power to the 
unit for a few seconds. Reapply power, and once the AirAura has rebooted and 
comes back to life, the new IP address will be valid. 
 

Configuring Remote GUI 

Now that AirAura has a valid network address the remote GUI must be 
configured so that it can find AirAura on the network.  
 
Install and then start the remote GUI. Then click Devices>Add... to bring up the 
Edit Device dialog. Entering a name is optional however it makes it easier to 
know which AirAura you are connected to.  
 

 

28

Содержание AirAura


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды