manualshive.com logo in svg

Vorsis AirAura, Руководство пользователя

Поделиться
Скачать
Vorsis AirAura Скачать руководство пользователя страница 25

If using the Analog L/R outputs pre-emphasized, navigate to the Output 
screen and select the checkbox for Analog L/R, either flat or de-emphasized 
noting that if pre-emphasis is enabled in the Input menu the FM outputs will 
be pre-emphasized unless De-Emphasis is also selected.  

 

Next adjust the FM Analog Output control to set the correct Left and Right 
output level. 

 

If using the Analog outputs ‘de-emphasized’ select the L/R De-Emphasized 
option. Then adjust the Analog Output control to set the correct Left and Right 
output level  

 

If using the AES Digital Outputs, connect it (them) to the equipment following 
the AirAura and adjust the AES Output level control in the Output Menu as 
appropriate. 

 

If using the Composite outputs associated with the rear panel BNC 
connectors, navigate to the Output menu and select the checkbox for MPX. 
Then adjust the TX 1 and TX 2 controls as necessary to set the correct 
modulation levels for your system.  

 
 
 

If the HD output is being used its output level can be adjusted from within the 
Output screen. When using the HD output we assume that you’re also going 
to need the FM diversity delay. Please adjust it as necessary for your system. 

 

 

20

Содержание AirAura


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды