manualshive.com logo in svg

Vorsis AirAura, Руководство пользователя

Поделиться
Скачать
Vorsis AirAura Скачать руководство пользователя страница 18

Also, pre-emphasis should 

always

 be applied by the audio processing, not the 

exciter. Modern FM audio processors have special and quite complicated but 
efficient circuits to deal with the challenges presented by the FM pre-emphasis 
curve and can provide very tight modulation control with low perceived distortion. 
FM exciters do not have this technology!  
 
 

EAS – United States Emergency Alert System 

If the EAS generator is placed before the AirAura, the levels of the signaling 
tones and FSK data can be disturbed if the processing (any processing, not just 
AirAura) is very aggressive. Therefore in this situation it is recommended that the 
EAS encoder be placed 

after 

the processing. 

 
If the EAS unit needs to be installed prior to AirAura and AirAura is operated 
aggressively, AirAura may need to be configured so that when the EAS tones are 
being sent AirAura is switched to a bypass mode or a less aggressive preset. 
This can easily be accomplished by using AirAura’s GPI interface and by 
assigning a special preset to the EAS function that has internal processing 
defeated and audio levels calibrated to provide proper modulation levels during 
EAS transmissions. 
 
 

Arbitron People Meter (PPM) 

Reports from the field indicate that AirAura favorably passes the data 
watermarking scheme used in the Arbitron People Meter rating service 
technology, regardless of the aggressiveness of the audio processing performed. 
 

 

13

Содержание AirAura


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды