Volvo Penta MD 11C/110S Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 44

background image

- 6 -

Reduce to idle and check that the engine is running smoothly.

Engage the control lever for gear-charging as follows:

Push in the red disengaging button when the lever is in neutral.
Release the button. The control lever can now be used both for
gear changing and engine speed.

RUNNING

The single lever control has both engine speed and manoeuvering
functions.
F = Forward
R = Reverse
N = Neutral
T = Engine speed control

To achieve good running economy, the engine should not be run
at max speed for a longer period.

Check during running that the temp meter, and also the lamps for
battery charging and low oil pressure are not lit. If an alarm system
is fitted and the siren sounds, -

Stop the engine immediately

and

investigate the cause.

SHUTDOWN PROCEDURE

Before shutdown

the engine should be allowed to idle for a few

minutes with the control lever in neutral.

Stop the engine

by pulling the stop control when the engine is

idling. Then turn back the key switch to the initial position.

«
...
6
7
8
9
10
...
»

Содержание MD 11C/110S













































Отзывы:

Нет отзывов

Похожие инструкции для MD 11C/110S

Бренд: Westerbeke Страницы: 60

Бренд: 3W Страницы: 20

Бренд: DLA Страницы: 7

Бренд: Globe Страницы: 11

Torqmotor TF Series

Бренд: Parker Страницы: 44

Бренд: V2 Страницы: 17

Бренд: Volkswagen Страницы: 64

Бренд: Toyota Страницы: 525

Бренд: MINN KOTA Страницы: 3

Бренд: MINN KOTA Страницы: 4

Бренд: TJERNLUND Страницы: 3

Бренд: Louvolite Страницы: 2

Бренд: Briggs & Stratton Страницы: 6

Бренд: Briggs & Stratton Страницы: 13

Бренд: Mitsubishi Страницы: 96

Бренд: Mitsubishi Страницы: 106

Бренд: Nakanishi Страницы: 2

Бренд: Nakanishi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды