Volvo Penta MD 11C/110S Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 44

background image

- 9 -

TECHNICAL DESCRIPTION

FUEL SYSTEM

The fuel system has a feed

pump with a fine filter, fuel filter with a fine filter insert,

injection pump and injectors. The feed pump is of the membrane type and has a hand
primer lever. There is a built-in cold start device. On the MD11C it is controlled
manually and on the MD17C it is operated automatically.

COOLING SYSTEM

The engine is cooled by sea water. The cooling system has a sea water pump and a
water distribution housing with a thermostat,

The sea water pump has an impeller made of neoprene rubber, which is driven via a
rubber flange from the camshaft.

The thermostat in the water distribution housing regulates the water flow, so that
water is always flowing in the exhaust manifold and out in the exhaust elbow,
regardless of whether the engine is cold or hot.

«
...
9
10
11
12
13
...
»

Содержание MD 11C/110S













































Отзывы:

Нет отзывов

Похожие инструкции для MD 11C/110S

Бренд: Jacobsen Страницы: 103

Бренд: Parker Страницы: 36

Бренд: Powerhouse Страницы: 31

Бренд: Stihl Страницы: 40

Бренд: Aerovent Страницы: 16

Cobalt IP Analog

Бренд: DCCconcepts Страницы: 2

Бренд: RCGF Страницы: 22

Бренд: V2 Страницы: 14

Бренд: Grundfos Страницы: 25

Бренд: Man Страницы: 50

Бренд: Hoval Страницы: 12

Бренд: A'OK Страницы: 7

Бренд: TOHATSU Страницы: 292

Бренд: Sachs Страницы: 52

Бренд: Orion Страницы: 4

Бренд: Volvo Penta Страницы: 100

Бренд: Volvo Penta Страницы: 104

Бренд: Toro Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды