Volvo Penta MD 11C/110S Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

Volvo Penta MD 11C/110S Скачать руководство пользователя страница 38

- 36 -

CHECKS AND SERVICE

OIL LEVEL IN DRIVE

Check every 14 days that the oil level is
within the dipstick's markings.

The oil dipstick has a bajonet fitting,
therefore it must be turned when lifting
and replacing. Note the sealing ring on
the dipstick. When checking the oil level
the dipstick must be turned to the locked
position.

Oil filling is done through the hole for the
dipstick. NOTE. Do not overfill.

Regarding

choice of oil, refer to

"Technical Data" page 37.

CHANGING DRIVE'S OIL

Remove the oil dipstick. Unscrew the
drain plug under the propeller gear
housing and let the oil drain off. Refit the
drain plug together with 0-ring. Fill with oil
through the dipstick's hole. NOTE. Do not
overfill. Regarding choice of oil, refer to
"Technical Data" page 37.

ZINC ANODE

Change the zinc anode if it has corroded
by more than 50 %. Remove the
propeller and spacer ring together with
the deflector and remove the two allen
screws holding the zinc anode. Scrape
the contact surface of the drive and fit a
new zinc anode. Make sure that there is
a good metallic contact between the zinc
anode and the drive. NOTE. The zinc
anode must not be painted.

«
...
36
37
38
39
40
...
»

Содержание MD 11C/110S













































Отзывы:

Нет отзывов