Volvo Penta MD 11C/110S Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 44

Volvo Penta MD 11C/110S Скачать руководство пользователя страница 20

- 18 -

CHECKS AND SERVICE

3. Re wiring between the charging circuits may not be carried out while the

engine is running.

Fit a Volvo Penta charging distributor
(accessory) on the alternator when more
than one battery is connected.

4. Observe the following whenever the
engine is started with an auxiliary
battery:

Let the ordinary battery remain
connected up. Connect the auxiliary
battery to the ordinary battery, plus to
plus and minus to minus. When the
engine has started, remove the auxiliary
battery, but do not break the ordinary
battery's wiring circuit.

5. Do not use a rapid charging unit when the alternator is connected to the battery.

6. Disconnect both the battery cables before doing any work on the alternator
equipment.

7. When electrical welding work is done to the engine or installation components,
disconnect the charging regulator cables at the alternator and insulate the cable ends.

8. Check regularly the belt tension and the cable connections.

Changing the fuse

A fusebox is mounted on the cylinder. A fuse breaks the electrical system when
overloaded. Re-connect the electrical system by transferring the cable connection to
the next fuse contact.

Starter motor and alternator

All work connected with the starter motor and alternator should be done by an
authorized service shop.

Inspection and control should be carried out in connection with a general inspection of
the engine.

«
...
18
19
20
21
22
...
»

Содержание MD 11C/110S













































Отзывы:

Нет отзывов