Volvo Penta MD 11C/110S Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

background image

- 16 -

CHECKS AND SERVICE

CHECKING AND REPLACEMENT OF PULLEY BELT

Check the belt carefully, both for wear and
cracks. Any sign of such, then the belt must
be replaced. Loosen the alternator mounting
bolts so that the belt can be removed. Dry
the pulley grooves before fitting the new belt.
Tension the belt so that the belt can only be
pressed down 5 mm (3/16") between the
pulleys. After a few hours running, recheck
belt tensioning and adjust if necessary.

RETIGHTENING CYLINDER HEAD BOLTS

Retighten each bolt

with a torque wrench

before

starting a new engine or an overhauled engine for
the first time, and after 20 hours of operation. The
valve clearance should always be checked after the
bolts have been retightened. Sequence for

tightening the bolts is shown in the figure opposite.

Torques:

Nos. 1, 2, 3 and 4 are torqued to 11 kpm (79 lbft)

Nos. 5 and 6 are torqued to 4.5 kpm (32 lbft)

CHECKING OF COOLING SYSTEM

The cooling system is working normally when the temp gauge is registering within the
green scale and the alarm (if fitted) is silent. Too high water temperature (red scale,
siren is sounding) can be due to the following: blocked water intake, defective
impeller or the flange in the sea water pump, faulty thermostat or temp sender.

Be

observant for water ingress

when working with the cooling system.

«
...
16
17
18
19
20
...
»

Содержание MD 11C/110S













































Отзывы:

Нет отзывов

Похожие инструкции для MD 11C/110S

Бренд: Fagor Страницы: 174

Бренд: Saab Страницы: 30

Бренд: FAAC Страницы: 7

Бренд: PCM Страницы: 83

Бренд: Vascat Страницы: 9

Бренд: Oriental motor Страницы: 8

Бренд: Moons' Страницы: 28

Vickers M2-200 Series

Бренд: Eaton Страницы: 16

290000 Vanguardv Gasoline

Бренд: Briggs & Stratton Страницы: 13

Бренд: Stobag Страницы: 12

Бренд: Raider Страницы: 28

ZA top SM225.40B

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: Mitsubishi Страницы: 61

Бренд: WilTec Страницы: 11

PowerMax SMX2HP35

Бренд: Seamax Страницы: 16

Бренд: Ford Страницы: 91

EM-PMI540-T3000

Бренд: Danfoss Страницы: 67

Бренд: Vascat Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды