Volvo Penta MD 11C/110S Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 44

background image

- 37 -

CHECKS AND SERVICE

COOLING SYSTEM

The cooling water intake for the engine's
cooling is located in the drives' lower gear
housing. Check when the boat is taken up
on land, that the grill and the round hole on
the front of the drive is free from marine
growth. If there is a danger of freezing and
when inhibiting, the cooling water is drained
from the drive and the pump by the cock on
the drive.

NOTE. When draining while the

boat is still afloat, the cock must be first
closed.

Do not forget to open the cock

before the engine is restarted.

GENERAL MAINTENANCE

While the boat is ashore, check the drive's paintwork and if necessary touch it with
genuine Volvo Penta paint. Paint the drive with anti-fouling paint which does not
contain copper. Check from outside that the rubber membrane over the drive's hull
aperture is in place.

Check from inside that the rubber seal between the bed and the drive is not
damaged. A damaged seal must be replaced.

RUNNING Important!

When charging from engine power to sail the propeller's rotation is stopped by
engaging reverse. During sailing the control shall be in the Neutral or Reverse
position, if a folding propeller is used. The control shall be in the Neutral position if a
fixed propeller is fitted.

TECHNICAL DATA, S-drive 1 10S

Sailboats drive, type  ...............................................................I ........................110S
Ratio  .............................................................................................................. 1.66:1
Oil capacity, sailboat drive, dm3 (Imp qts = US qts)  .............................. 1,8 (1,62-1,9)

Oil quality (same as engine) ..................................................Diesel lubricating oil CD
Viscosity  ................................................................................................. SAE 20W

1)

Total weight, MD11C/110S kg (lbs) ............................................................ 247 (545)
MD17C/110S kg (Ibs) ................................................................................ 317 (695)

1) Volvo Penta CD oil, Double grade

«
...
37
38
39
40
41
...
»

Содержание MD 11C/110S













































Отзывы:

Нет отзывов

Похожие инструкции для MD 11C/110S

Бренд: O.S. engine Страницы: 21

Бренд: O.S. engine Страницы: 25

Бренд: 3T-Components Страницы: 20

Бренд: ZAFFER Страницы: 28

Бренд: Hoval Страницы: 12

Бренд: Lombardini Страницы: 88

Бренд: DoorHan Страницы: 16

Бренд: Doosan Страницы: 179

Бренд: Becker Страницы: 24

Бренд: SSANGYONG Страницы: 14

Бренд: YS Страницы: 2

Megatorque PS Series

Бренд: NSK Страницы: 370

Бренд: Yanmar Страницы: 240

EPA04 Series 40

Бренд: Detroit Diesel Страницы: 158

Бренд: Uebelhoer Bros Страницы: 12

Бренд: NACIONAL MOTOR Страницы: 72

Бренд: Traxxas Страницы: 4

Бренд: Zenoah Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды