Volvo Penta MD 11C/110S Скачать руководство пользователя страница 29

Страница: 29 / 44

- 27 -

TECHNICAL DATA

Technical data

General

Engine designation

MD11C

MD17C

Number of cylinders

Propeller shaft output kW (hp) at 41.7 r/s (2500 rpm)

17 (23)

25 (35)

Max operating speed rev/sec (rpm)

41.7 (2500)

Cylinder diameter, mm (inches)

88,9 (3,5)

Stroke, mm (inches)

90,0(3,55)

Displacement, dm

(in

)

1,12 (68,3)

1,68

(102,4)

Compression pressure kp/cm

(psi) (starter motor speed)

20-24 (144-173)

Idling speed r/s (rpm)

11-13 (650-780)

Direction of rotation looking at flywheel

Clockwise

Max rearwards inclination, boat underway

15°

Max sideways inclination, boat underway

15°

Engine weight, incl. reverse gear, kg (Ibs)

230 (505)

290( 640)

Valves

Valve clearance, hot engine

inlet, mm (in.)

0,30 (0.012)

exhaust mm (in.)

0,35 (0.014)

Decompression device, max downwards movement of exhaust
valve, mm (in.)

0,5 (0,0197)

Lubrication system

Engine

Oil capacity dm3 (imp qts=US qts) excl.

filter

2,6(2,2=2,7)

4,2(3,6=4,

incl. filter

2,9

(2,5=3,05)

4,5

(3,8=4,7)

Oil quality

Diesel lubricating oil CD

Viscosity

above +10C (50F)

SAE 20

below +10C (50F)

SAE 10W3

Oil pressure, hot engine, idling speed kp/cm

(psi)

0,8-1,5 (11,2-21)

at full speed kp/cm

(psi)

2,0-3,0 (28-42)

MSB reverse gear with reduction

Oil capacity, dm

(Imp qts=US qts)

0,60 (0,5-0,6)

Oil quality (same as for engine)

Diesel lubricating oil CD

Viscosity

above + 1° C (50°F)

SAE 20

below +10° C (50°F)

SAE 1OW

Cooling system

Thermostat, starts opening at °C (°F)

60° (140°)

57° (135°)

fully open at °C (°F)

75° (168°)

72° (160°)

1)Propeller shaft output according to DIN Lesitung B fur Dauerbetrieb.
2) Volvo Penta CID oil, Double grade.
3) Volvo Penta CD oil, Single grade.

Содержание MD 11C/110S













































Результаты поиска

Содержание MD 11C/110S

Отзывы:

Volvo Penta MD 11C/110S, Инструкция, Страница: 29 / 44

Результаты поиска

Содержание MD 11C/110S

Отзывы: