Volvo Penta D5 Скачать руководство пользователя

Страница: 25 / 80

Adjusting the friction brake

The lever is fitted with a friction brake to allow
adjustment for easier or stiffer movement as required.
The friction brake only affects movement of the throttle
control lever.

1 Lift away the cover from the control. On side-

mounted controls the lever must be removed first.

2 Move the lever to the half throttle/astern position.

3 Adjust the friction brake by turning the screw

clockwise (+) for stiffer lever movement, and
counterclockwise (-) for easier movement.

4 Replace the cover and the lever.

Dual lever control

Maneuvering

A twin-lever control has separate levers for the
gearshift function (

) and rpm control (throttle) (

The engine can only be started with the control lever
in the neutral position.

Black lever (1)
N

= Neutral position. Reverse gear/drive disengaged

and engine at idle.

= Reverse gear/drive engaged for forward motion.

= Reverse gear/drive engaged for rearward

motion.

Red lever (2)

Engine rpm control (throttle).

Control A

Control B

Instruments and Controls

47713336 03-2021 © AB VOLVO PENTA

Содержание D5

















































































Результаты поиска

Содержание D5

Отзывы:

Похожие инструкции для D5

Бренды по названию

Популярные бренды

Volvo Penta D5, Руководство оператора

Результаты поиска

Содержание D5

Отзывы:

Похожие инструкции для D5

Бренды по названию

Популярные бренды