Volvo Penta D5 Скачать руководство пользователя | Manualshive

Страница: 61 / 80

background image

Replacing Battery

IMPORTANT:

Make sure that the new battery fulfills the specifications
in

Technical Data

. Read the information supplied with

the battery before you begin the installation.

IMPORTANT:

Do not disconnect the batteries with the engine
running.
Sensitive electrical components can be immediately
damaged.

WARNING!

Never confuse the positive and negative poles on the
batteries. Risk of arcing and explosion.

Disconnecting (A)

1 Untighten the nut and remove the – cable (black).

2 Untighten the nut and remove the + cable (red).

Remove the battery.

Connecting (B)

Place the new battery.

1 Connect the + cable (red) to the + pole on the

battery and tighten the nut.

2 Connect the – cable (black) to the – pole on the

battery and tighten the nut.

NOTICE!

Hand in the old battery to a re-cycling station.

Electrical Installations

An incorrectly designed electrical installation may
generate leakage current from the electrical system.
Leakage current can in turn render galvanic protection
inadequate in respect of propellers, propeller shafts,
rudder posts, the keel etc., and may cause damage
through electrochemical corrosion.

Maintenance

47713336 03-2021 © AB VOLVO PENTA

59

«
...
59
60
61
62
63
...
»

Содержание D5

















































































Отзывы:

Нет отзывов

Похожие инструкции для D5

Бренд: Yamaha Страницы: 7

Бренд: Eaton Страницы: 12

E-II SGM H Series

Бренд: YASKAWA Страницы: 408

Бренд: E-MAG Страницы: 30

Бренд: Amico Страницы: 47

Бренд: ZAFFER Страницы: 28

MotorLift RA20F

Бренд: Chamberlain Страницы: 24

Бренд: Chamberlain Страницы: 40

DYNAMIC LINE III

Бренд: KEB Страницы: 60

Бренд: LONCIN Страницы: 44

Бренд: Stiga Страницы: 168

Бренд: CHEE SIANG INDUSTRIAL Страницы: 57

Бренд: Tecno Automazione Страницы: 11

BASIC AUTO AM45

Бренд: A'OK Страницы: 6

Бренд: RMS Страницы: 41

Бренд: LIMBACH Страницы: 3

Бренд: Swiss Rotors Страницы: 26

Бренд: Ford Страницы: 173

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды