Volvo Penta D5 Скачать руководство пользователя

Страница: 65 / 80

Transmission Oil, Change

The oil can be drained by removing the drain plug on
the reverse gear or by the using the manual oil drain
pump.

1 Remove the dipstick. Connect a hose from the oil

scavenging pump to the dipstick tube.

2 Set the knob under the pump housing in position for

pumping the reverse gear.

3 Suck the oil up and put the dipstick back.

4 Fill with oil through the filler opening on top of the

reverse gear. Please refer to

Technical

Data, page 73

for oil grade and capacity.

IMPORTANT!

Never over-fill the reverse gear.

5 Start the engine and run until the reverse gear has

reached operating temperature.

6 Check the oil level with the engine at low idling

speed and the controls in neutral position. The oil
level must reach to the upper mark on the dipstick.
Top up oil if needed.

Maintenance

47713336 03-2021 © AB VOLVO PENTA

Содержание D5

















































































Результаты поиска

Содержание D5

Отзывы:

Похожие инструкции для D5

Бренды по названию

Популярные бренды

Volvo Penta D5, Руководство оператора

Результаты поиска

Содержание D5

Отзывы:

Похожие инструкции для D5

Бренды по названию

Популярные бренды