Volvo Penta D5 Скачать руководство пользователя

Страница: 64 / 80

Reversing gear

Oil level, checking and topping up

Checking

Check the oil level when the reverse gear has reached
working temperature, with the engine at idle and
control lever at neutral.

1 Pull up and dry off the dipstick (

) and insert in

the reverse gear again.

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and
hot surfaces.

2 Pull out the dipstick again and check the oil level.

The correct level is between MAX and MIN
marks.

Filling

Top up with oil as required through the filler opening
(

) on the top of the reverse gear, refer to

Technical

Data, page 73

for oil grade and volume.

IMPORTANT!

Never over-fill the reversing gear. The oil level must
always be within the recommended range.

Maintenance

47713336 03-2021 © AB VOLVO PENTA

Содержание D5

















































































Результаты поиска

Содержание D5

Отзывы:

Похожие инструкции для D5

Бренды по названию

Популярные бренды

Volvo Penta D5, Руководство оператора

Результаты поиска

Содержание D5

Отзывы:

Похожие инструкции для D5

Бренды по названию

Популярные бренды