Volvo Penta D5 Скачать руководство пользователя | Manualshive

Страница: 12 / 80

background image

Proper fuel quality

IMPORTANT:

Always use the fuel recommended by Volvo Penta.
See

Technical Data

in Operator’s Manual. Other fuel

can damage the engine.
Wrong fuel quality can also lead to higher service
costs.

WARNING!

Risk of personal injury.
Wrong fuel quality in a diesel engine can cause the fuel
control mechanism to bind which can cause the engine
to overspeed!

Legal requirements to use proper fuel

IMPORTANT:

To meet regulatory requirements for certified emission
levels must always recommended fuel according to

Technical Data

in the Operator’s Manual be used.

At any leak detection on the fuel system

WARNING!

Wear safety goggles!
Be extremely careful when searching for leaks in the
fuel system high-pressure circuits. There is very high
pressure in the jet from pipes and injectors. The fuel
may penetrate the tissue and cause serious risk of
blood infection (septicemia).

Handling of fuel pipes

IMPORTANT:

High pressure pipes for fuel must not be bent or
straightened under any circumstances. Cracks may
occur. Damaged pipes must be replaced.

Safe handling of batteries

WARNING!

Risk of fire and explosion. Never allow an open flame
or electric sparks near the batteries.

A spark caused by an incorrectly connected battery
can be enough for the battery to explode with serious
injuries.

Do not touch the connections during start attempts.
Sparking hazard! Do not lean over batteries.

P0024477

P0024488

Safety Information

10

47713336 03-2021 © AB VOLVO PENTA

«
...
10
11
12
13
14
...
»

Содержание D5

















































































Отзывы:

Нет отзывов

Похожие инструкции для D5

Бренд: KCFA Страницы: 2

Бренд: Nanni Страницы: 24

Бренд: Iveco Motors Страницы: 60

Бренд: Iveco Страницы: 206

Бренд: Volvo Penta Страницы: 40

Бренд: Volvo Penta Страницы: 48

Бренд: Volvo Penta Страницы: 76

Бренд: Volvo Penta Страницы: 124

Бренд: Volvo Penta Страницы: 140

Бренд: O.S. engine Страницы: 13

MAX-15CV Series

Бренд: O.S. engine Страницы: 30

Бренд: Texas Equipment Страницы: 25

Бренд: Sisu Diesel Страницы: 116

Metaphaser MP-LE1007

Бренд: Metaphase Technologies Страницы: 35

Бренд: Honda Страницы: 60

Бренд: Stober Страницы: 48

Бренд: WilTec Страницы: 16

Бренд: WilTec Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды