Volvo Penta D5 Скачать руководство пользователя | Manualshive

Страница: 43 / 80

background image

Drive belt, check and change

WARNING!

Stop the engine before doing any maintenance work.

Check

Check belt tension and condition regularly. If the belt
is too tight it can damage bearings and if it is too loose
it may slip. Check and adjust after operation when the
belt is warm.

IMPORTANT!

Always change a belt, which looks worn or cracked.
Belts which operate in pairs must be changed
together.

Adjust and replace

Adjust and change as necessary. It can generally be
said that the belts are correctly tensioned if they can
be pressed down 10 mm (3/8") by thumb pressure.
Clean the belt grooves before fitting a new belt.

Alternator belt

Adjust

1 Loosen the screw (

5

).

2 Push the alternator belt pulley (4) to the right

until the belt is correctly tensioned.

3 Tighten the screw.

Replace

1 Remove the belt for the fuel pump as described

in “

Coolant pump / Fuel pump, Adjust

”

2 Loosen the screw (

5

).

3 Push the alternator belt pulley (4) to the right

until the correct belt tension is achieved.

4 Tighten the screw (

5

).

5 Replace the belt for the fuel pump and tension

the belt as described in

Coolant pump / Fuel

pump, Adjust

”.

Maintenance

47713336 03-2021 © AB VOLVO PENTA

41

«
...
41
42
43
44
45
...
»

Содержание D5

















































































Отзывы:

Нет отзывов

Похожие инструкции для D5

Бренд: GAS GAS Страницы: 71

Бренд: MAK Страницы: 2027

Бренд: Baratza Страницы: 5

Бренд: Tanaka Страницы: 11

Бренд: Northern Lights Страницы: 36

Бренд: Northern Lights Страницы: 45

Бренд: Northern Lights Страницы: 56

Бренд: Volvo Penta Страницы: 36

Бренд: Becker Страницы: 24

Бренд: Metronic Страницы: 28

50-400 V CA Series

Бренд: TEM Страницы: 44

Бренд: Honda Страницы: 45

Бренд: Barrus Страницы: 88

Бренд: Motus Страницы: 32

Бренд: Briggs & Stratton Страницы: 112

Бренд: Briggs & Stratton Страницы: 13

Бренд: Grundfos Страницы: 36

Powerful G3.0 Engine

Бренд: HPI Racing Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды