Vollrath STL-80SS Скачать руководство пользователя страница 20

Страница: 20 / 74

Electronic Parts and Connections (See Figure 6)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

STOEELE906

FLAVOR 10 COLOR TOUCH PANEL

Control system for the unit.

STOEMIS3214

TOUCH PANEL MOUNTING
BRACKET ASSEMBLY

Secures the Touch Panel to the freezer.

STOEMIS3214A

TOUCH PANEL MOUNTING PLATE

1 ea. Attaches the Touch Panel to the anchor bracket.

STOEMIS3214B

MOUNTING ANCHOR BRACKET

1 ea. Allows the bracket to be angled up or down.

STOEMIS3214C

MOUNTING BASE PLATE

1 ea.

Creates a mounting base for the bracket
assembly.

STOEFAS2170

M4 X 8 PHILLIPS SCREW

4 ea. Secures the mounting plate to the Touch Panel.

STOEFAS2174

1/4 - 20 NYLON LOCK NUT S.S.

2 ea. Secures the anchor bracket in a fixed position.

STOEMIS3076

ADHESIVE PAD

1 ea. Secures the mounting bracket to the freezer.

STOEFAS2172

1/4-20 X 1/2 HEX BOLT

2 ea. Hinges the Touch Panel plate and anchor bracket.

STOEFAS2023

MOUNTING BRACKET KNOB

4 ea. Secures the anchor bracket to the base plate.

STOEFAS2171

M4 LOCK WASHER

4 ea. Secures the connection between screw and plate.

STOEFAS2173

FLAT WASHER 18-8 S.S.

2 ea. Secures the connection between bolt and nut.

STOEMIS3004

CTP ETHERNET CABLE PLATE

Converts the touchscreen cable hole to an
ethernet cable hole.

STOEMIS3026S

TOUCH PANEL CABLE CASING

Conceals and protects the Touch Panel cable, as
well as attaches it to the freezer.

STOEELE525M

MALE TO MALE 48” SWITCH
EXTENSION

Connects Touch Panel to the freezer switch.

STOECAB137-A

ELECTRONICS COVER

Protects and covers electronics microprocessor.

STOEFAS2014

8-32 X 1/2" PAN HEAD

16 Secures various parts within the top of unit.

STOEMIS3150

FLAVOR BURST LOGO DECALS

Displays Flavor Burst trademark logo.

STOECAB156

CONNECTOR SHIELD

Protects power cables from liquids.

STOE

ELE485CTP

120V POWER ENTRANCE MODULE

Provides a power connection to the outside of the
cabinet.

STOEELE932

PUMP & SANITIZER CABLE
HARNESS

Provides power to syrup & sanitizer pumps.

STOEELE933

POWER SUPPLY JUMPER CABLE

Connects the power supply to the electronics
board.

STOEELE931

EXTERNAL ROTOR CABLE

Connects the drive motor to the back of the
cabinet.

STOEINJ330TS

INJECTOR MOTOR ASSEMBLY

Supplies power to Motor which turns gears.

STOEELE911

ELECTRONICS BOARD

Provides power to the system.

STOEFAS2024

8-32 X 1/4 PAN HEAD SCREW

Secures power supply to the base panel.

STOEFAS2035

8-32 NUT - EXT. LOCK WASHER

Secures ground wire to screw and
Panel and the Electronics Box to the panel.

STOEFAS2042

4/40 LOCK NUT

Secures the Ethernet plate and screws.

STOEELE930

INTERNAL ROTOR CABLE

Connects the external rotor cable to the
electronics board.

STOEFAS2008

4-40 X 3/8" PAN HEAD SCREW

Attaches the ethernet plate to the panel.

STOEMIS3216

CLOSURE PLUG 5/8 INCH

Closes up extra opening in the base panel.

STOEELE434

POWER CABLE

Supplies the electronics board with power.

STOEELE927

RJ45 ETHERNET CABLE GLAND

Secures the Ethernet cable to the cabinet.

Содержание STL-80SS











































































Результаты поиска

Содержание STL-80SS

Отзывы:

Похожие инструкции для STL-80SS

Бренды по названию

Популярные бренды

Vollrath STL-80SS, Руководство оператора

Результаты поиска

Содержание STL-80SS

Отзывы:

Похожие инструкции для STL-80SS

Бренды по названию

Популярные бренды