Vollrath STL-80SS Скачать руководство пользователя страница 18

Страница: 18 / 74

Sanitizer Pump and Related Parts (See Figure 5)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

STOESAN748

SANITIZER PUMP ASSEMBLY

Supplies sanitizer to flush tube.

STOETUB807

SANITIZER TUBE REPLACEMENT

Transports sanitizer through pump.

STOESYR927

INTERNAL 9-TUBE ASSEMBLY

Transports syrup from bags to flavor 9-Tube
Assembly.

STOEMIS3023

DUST CAP

1 ea. Cover to protect end of flavor lines.

STOEFAS2051

ROLLED FLANGE EYELET

9 ea.

Creates tension for tighter fit 1 per
pump, 9 per tube assembly.

STOEROT510

LINE COUPLER

1 ea. Holds flavor lines in place.

STOEROT512

TUBE CONNECTOR BODY

1 ea.

Connects internal 9-Tube Assembly to
flavor lines.

STOEROT511

LINE COUPLER NUT

1 ea.

Connects flavor lines to the internal
9-Tube Assembly.

STOESYR900

4' 9-TUBE ASSEMBLY TUBES

9 ea.

Transports syrup and sanitizer from
pumps to Injector Assembly.

STOEELE932

PUMP & SANITIZER CABLE
HARNESS

Provides power to the syrup and sanitizer
pumps.

STOEFIX1053

SANITIZER PUMP T CONNECTOR

Connects sanitizer line to flush adapter
and pump lines.

STOEMIS3028-80

FLUSH TUBE ASSEMBLY

Connects with flavor line to flush with
sanitizer solution.

STOEFIX1054

1/4” ID HOSE BARB SHUTOFF

1 ea.

Connects to the syrup line to flush sanitizer
solution through it.

STOEFIX1051

1/4” ID HOSE BARB ELBOW

1 ea.

Connects to the syrup line to flush sanitizer
solution through it.

STOESYR931

CLEAR TUBING

3 ea.

Transports sanitizer to Pump Flush Adapter
fitments.

STOEFIX1046

FLUSH TUBE “Y” CONNECTOR

1 ea. Splits sanitizer flush tube into two tubes.

STOEFIX1023

3/16" X 3/16" BARB TUBE CONNECT

Splices together flush tubes.

STOETUB803

.17 x 1/4 LDPE TUBING-PER FOOT

Transports sanitizer solution from tank
to sanitizer pump.

STOEFIX1035

1/4 TO 3/16 OD REDUCING UNION

Connects elbow to sanitizer line.

STOEFIX1042

TUBE-TO-TUBE ELBOW

Connects pump tube to reducing union.

STOESYR931

CLEAR TUBING

Transports sanitizer to Pump Flush Adapter.

STOESAN740

SANITIZER TANK ASSEMBLY

Holds sanitizer solution and delivers it to the
Flavor Burst cabinet and Injector Assembly.

12A

STOESAN701

SANITIZER TANK

1 ea. Holds sanitizer solution.

12B

STOESAN734

HAND PUMP ASSEMBLY-FLUTED
TANK

1 ea. Seals sanitizer tank and adds pressure

when needed.

12C

STOETUB803

.17 x 1/4 LDPE TUBING-PER FOOT

1 ea. Transports sanitizer solution from tank

to sanitizer pump.

12D

STOESAN715

SUPPLY TUBE CAP

1 ea. Fastens grommet securely to tank.

12E

STOERUB616

FEEDER TUBE RUBBER GROMMET

1 ea. Holds sanitizer tube in place and seals

tank hole.

12F

STOESYR902

SANITIZER SUPPLY TUBING

1 ea. Supplies sanitizer from sanitizer tank.

12G

STOEFIX1036

1/4" TO 1/4" OD UNION ELBOW

1 ea. Connects sanitizer tube to supply tube.

Содержание STL-80SS











































































Результаты поиска

Содержание STL-80SS

Отзывы:

Похожие инструкции для STL-80SS

Бренды по названию

Популярные бренды

Vollrath STL-80SS, Руководство оператора

Результаты поиска

Содержание STL-80SS

Отзывы:

Похожие инструкции для STL-80SS

Бренды по названию

Популярные бренды