Vollrath STL-80SS Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 74

background image

51

Draw Switch Options

When the draw spout is activated, the switch
relays the signal to the Flavor Burst

®

system,

telling it to activate the pumps and syrups as
product is drawn from the spout. The STL-
80SS includes two options for the draw switch.

PREFERED METHOD: The draw switch
extension should be used with freezers with an
integrated switch already installed. If your
freezer does not have an integrated switch,
contact White Glove Service to order and install
the integrated switch kit #2209616.

OPTIONAL METHOD: The other option is a
draw handle switch. It is included in the Spare
Parts Kit for freezers lacking the internal switch.

Installing the Draw Switch Extension

1. Ensure the straight end of the switch

extension is connected to the “PORT 1”
switch port on the underside of the Touch
Panel.

NOTE:

WHILE “PORT 2” SWITCH PORT IS

ALSO A VALID PORT, IT IS TEMPORARILY
PLUGGED TO AVOID CONFUSION. YOU
WILL ACTIVATE THE PORT YOU USE WHEN
YOU GO THROUGH THE EQUIPMENT
SETUP WIZARD PROGRAM ON YOUR
COLOR TOUCH PANEL LATER.

2. Connect the angled-end of the switch

extension to the switch jack underneath the
freezer overhang, near the draw handle.

3. Ensure the connections are fully engaged.

Installing the Draw Handle Switch

1. Ensure the straight end of the switch

extension is connected to the “PORT 1”
switch port on the underside of the Touch
Panel.

NOTE:

WHILE “PORT 2” SWITCH PORT IS

ALSO A VALID PORT, IT IS TEMPORARILY
PLUGGED TO AVOID CONFUSION. YOU
WILL ACTIVATE THE PORT YOU USE WHEN
YOU GO THROUGH THE EQUIPMENT
SETUP WIZARD PROGRAM ON YOUR
COLOR TOUCH PANEL LATER.

2. Clip the draw handle switch onto the handle

and slide it up the handle until the switch is
within grasping range.

3. Connect the switch extension to the draw

switch jack and ensure the connection is
fully engaged.

NOTE:

IF YOUR FREEZER DOES NOT HAVE

AN INTERNAL SWITCH JACK AND THE
SPARE DRAW HANDLE SWITCH DOES NOT
FIT YOUR FREEZER, CONTACT WHITE
GLOVE SERVICE FOR MORE OPTIONS.
WHEN POSSIBLE, ORDER AND INSTALL
THE INTEGRATED SWITCH KIT #2209616.

«
...
52
53
54
55
56
...
»

Содержание STL-80SS











































































Отзывы:

Нет отзывов

Похожие инструкции для STL-80SS

Бренд: FBD Страницы: 2

Бренд: icetro Страницы: 49

Бренд: Canature WaterGroup Страницы: 36

Бренд: Bunn Страницы: 2

Бренд: Hilti Страницы: 240

AO-WH-SOFT-450T

Бренд: A.O. Smith Страницы: 49

Water Filter CB20-302E

Бренд: Everpure Страницы: 2

Бренд: Everpure Страницы: 2

Бренд: Everpure Страницы: 2

Better Packages TERZETT 754

Бренд: HADE Страницы: 235

Lowerator HMCTR-1020

Бренд: APW Wyott Страницы: 2

SOFT DUOMATIK EVOLINE

Бренд: Evo-water Страницы: 24

Бренд: Verbatim Страницы: 13

Бренд: Graff Страницы: 3

H2O-PRO H2O-PRO

Бренд: H2O International Страницы: 4

Бренд: Cuno Страницы: 21

Бренд: Genius Ideas Страницы: 6

Pure Water Dispenser 500 Series

Бренд: SPARKLETTS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды