Vollrath STL-80SS Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 74

background image

3

FCC Conformity Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure and SAR Statements SAR Statement.
The Flavor 10* has been tested for body-worn Specific Absorption Rate (SAR) compliance. The FCC
has established detailed SAR requirements and has established that these requirements. RF Exposure
Information. The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to
be compliant to the requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4)
addressing RF Exposure from radio frequency devices. This model meets the applicable government
requirements for exposure to radio frequency waves. The highest SAR level measured for this device
was 0.293W/kg.

*The Flavor 10 is also referred to as the Touch Panel throughout this manual.

«
...
4
5
6
7
8
...
»

Содержание STL-80SS











































































Отзывы:

Нет отзывов

Похожие инструкции для STL-80SS

Бренд: Yaesu Страницы: 16

Бренд: Ugolini Страницы: 40

Бренд: Delfield Страницы: 2

LOGIX 255-760 Meter

Бренд: Autotrol Страницы: 15

Бренд: Parweld Страницы: 12

Бренд: Kobra Страницы: 64

Бренд: Talent Страницы: 28

Бренд: BestWater Страницы: 70

WP3812 Micro X-Pure

Бренд: Philips Страницы: 36

Бренд: Hongda Holding Water Technology Страницы: 4

Бренд: Viqua Страницы: 4

Бренд: AOX Страницы: 8

Бренд: Silver King Страницы: 2

Бренд: Silver King Страницы: 12

Бренд: Silver King Страницы: 12

Бренд: Silver King Страницы: 20

Бренд: Silver King Страницы: 10

Бренд: Lancaster Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды