VOLKTEK NSH-580 Скачать руководство пользователя страница 42

Страница: 42 / 101

VOLKTEK NSH-580 MANAGED 24-PORT 10/100 + 4 G COMBO L3 SWITCH

VRRP

7.7 Bridge

The Bridge page group contains Layer 2 configurations like link aggregation, STP, etc.

7.7.1 Spanning

Tree

This section configures three types of Spanning Tree Protocol.

7.7.1.1 STP

Status

The first page, “

STP Status

”, can disable or enable STP. There are three modes of STP,

RSTP and MSTP can be enabled. If MSTP is enabled, the following four attributes are
enabled at the same time:

Region Name:

An alphanumeric configuration name

Revision:

A configuration revision number to identify the region along with the

Region Name

Instance ID:

A STP instance, you can configure MSTP on your Switch to map

multiple VLANs into a single STP instance.

VLAN Group:

A group associates each of the potential 4094 VLANs to the given

instance.

Содержание NSH-580






































































































Результаты поиска

Содержание NSH-580

Отзывы:

Бренды по названию

Популярные бренды

VOLKTEK NSH-580, Руководство пользователя

Результаты поиска

Содержание NSH-580

Отзывы:

Бренды по названию

Популярные бренды