manualshive.com logo in svg

VOLKTEK NSH-580, Руководство пользователя

Поделиться
Скачать
VOLKTEK NSH-580 Скачать руководство пользователя страница 38

VOLKTEK NSH-580 MANAGED 24-PORT 10/100 + 4 G COMBO L3 SWITCH 

 

OSPF – Area 

7.6.4 Multicast 

Route 

This function is used to configure Multicast Route feature. It offers two different methods 
including DVMRP and PIM-DM to establish multicast route. Also, IGMP will be 
automatically enabled/disabled with Multicast Route Protocol. It allows hosts to 
communicate their specific data destined for a specific multicast group. Multicast route 
protocol uses this information to build and maintain multicast distributed tree. 

7.6.4.1  M.R. – IGMP 

This command is used to configure the IP multicast route mode and IGMP parameters. 

IP Multicast Route Mode:

 Configure a multicast route protocol to run or disable. 

IGMP Version:

 Select which version of IGMP run. Default value is V2. 

IGMP Query Interval: 

Set the number of seconds between two query packets. Default 

value is 125 sec. 

IGMP Query-Max-Response:

 Set response time when host reports its multicast group. 

Default value is 10 sec. 

NOTE: 

When setting IGMP, select the corresponding interface to configure 
parameters then click on the 

Modify 

button. The field you changed will 

update the content in the display window. To save any changes and make 
them effective immediately, click 

Submit

. Click 

Refresh

 to refresh the 

settings. 

 

  

37

Содержание NSH-580






































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды