Visonic POWERMAXCOMPLETE PANEL -, Руководство по установке

Страница: 34 / 48

34 D-303983 PowerMaxComplete Installer's Guide
restart>reentry - Exit delay restarts when the door is
reopened during exit delay. The restart occurs once only.
Restarting the exit delay is helpful if the user re-enters
immediately after going out to retrieve an item that was left
behind.
door/fob/timer - When the door is closed, by pressing the
aux button on the keyfob*, or when the exit delay has
expired, whichever first.
* Only when defined as "skip exit delay" (see section
4.4.17).
KEYFOB/KEYPAD PANIC
[Fig 4.17.3(4)]
Define the devices that cannot trigger a panic alarm.
DD243
– MCT-234.
all - All devices can trigger a panic alarm
CONFIRM ALARM
[Fig 4.17.3(5)]
Define a specific time period that if 2 successive alarms
occur, the second alarm will be considered as a
confirmed alarm , (see REPORT CNFRM ALARM below).
The options are: in 30 minutes , in 45 minutes , in 60
minutes and in 90 minutes .
CONFIRM PANIC
[Fig 4.17.3(6)]
A confirmed panic alarm is reported if one of the following
occurs within the confirmation time:
a) A second panic device is activated.
b) A second panic alarm on the same device is activated.
c) A tamper event is activated (not from the zone / device
that initiated the panic alarm). When tamper is the
cause of the confirmed panic alarm, the tamper event
and the confirmed panic alarm must be reported.
The options are: in 4 hours , in 8 hours , in 12 hours , in
20 hours , in 24 hours and disabled .
RPT CNFM ALRM
[Fig 4.17.3(7)]
Define whether the system will report a confirmed alarm.
Disable - The system will not report a confirmed alarm.
Enable - The system will report a confirmed alarm.
bypass - The system will report a confirmed
alarm and will bypass all alarmed open zones when the
siren ends or when the confirmation timer expires.
ENTRY DELAY 1&2
[Fig 4.17.3(8)&(9)]
Two different entry delays allow the user to enter the
protected site (while the system is in the armed state) via 2
specific doors and routes without causing an alarm.
Following entry, the user must disarm the control panel
before the entry delay expires. Slow-rate warning beeps
start sounding once the door is opened, until the last 10
seconds of the delay, during which the beeping rate
increases. Locations No. 1 (entry delay 1) and 2 (entry
delay 2) allow you to program the length of these delays.
The options are:
10s , 15s , 30s , 45s , 60s , 3m and 4m .
4.17.4 CP01 Setup
[Fig 4.17.4)]
– USA standard
CANCEL ANNOUNCEMENT
[Fig 4.17.4(1)]
Define whether a special beep will sound when an alarm
cancel event is sent to the central station.
The options are:
enable and disable .
ABORT ANNOUNCEMENT
[Fig 4.17.4(2)]
Define that when the user disarms the system within the
allowed abort interval, a special beep will sound to indicate
"no alarm transmission".
The options are:
enable and disable .
END EXIT MODE
[Fig 4.17.4(3)]
Define how the exit delay is terminated or restarted.
fob/timer - By pressing the aux button on the keyfob*, or
when the exit delay has expired, whichever first.
door/fob only - When the door is closed, or by pressing
the aux button on the keyfob*, whichever first.
arm home
– During exit delay if the door was not
opened, the alarm system will be armed Home instead of
armed Away .
restart>reentry - Exit delay restarts when the door is
reopened during exit delay. The restart occurs once only.
Restarting the exit delay is helpful if the user re-enters
immediately after going out to retrieve an item that was left
behind.
door/fob/timer - When the door is closed, by pressing the
aux button on the keyfob*, or when the exit delay has
expired, whichever first.
* Only when defined as "skip exit delay" (see section
4.4.17).
ENTRY DELAY 1&2
[Fig 4.17.4(4)&(5)]
Two different entry delays allow the user to enter the
protected site (while the system is in the armed state) via 2
specific doors and routes without causing an alarm.
Following entry, the user must disarm the control panel
before the entry delay expires. Slow-rate warning beeps
start sounding once the door is opened, until the last 10
seconds of the delay, during which the beeping rate
increases. Locations No. 1 (entry delay 1) and 2 (entry
delay 2) allow you to program the length of these delays.
The options are:
30s , 45s , 60s , 3m and 4m .
ABORT TIME
[Fig 4.17.4(6)]
Select the length of time allowed by the system to abort an
alarm (not applicable to alarms from FIRE, 24H SILENT,
EMERGENCY, GAS FLOOD and TEMPERATURE zones).
The PowerMaxComplete is programmed to provide an
“abort interval” that starts upon detection of an event.
During this interval, the buzzer sounds a warning but the
siren remains inactive and the alarm is not reported. If the
user disarms the system within the allowed abort interval,
the alarm is aborted.
The options are:
abort time 15s , abort time 30s and abort
time 45s
ALARM CANCEL
[Fig 4.17.4(7)]
Define the ”cancel alarm” period that starts upon reporting
an alarm to the central station. If the user disarms the
system within that time period, a “cancel alarm” message
is sent to the central station.
The options are:
in 5 minutes , in 15 minutes , in 60
minutes and in 4 hours .