background image

2

These units 

MUST

use one of the vent systems

described in the Installing the Fireplace section of the

Installers Guide

.

NO OTHER 

vent systems or

components

MAY BE USED.

This gas fireplace and vent assembly 

MUST

be

vented directly to the outside and 

MUST NEVER 

be

attached to a chimney serving a separate solid fuel
burning appliance. Each gas appliance 

MUST USE

a separate vent system. Common vent systems are

PROHIBITED

.

INSPECT

the external vent cap on a regular basis to

make sure that no debris is interfering with the air
flow.

The glass door assembly 

MUST

be in place and

sealed, and the trim door assembly 

MUST

be in

place on the fireplace before the unit can be placed
into safe operation.

DO NOT OPERATE 

this appliance with the glass

door removed, cracked, or broken. Replacement of
the glass door should be performed by a licensed or
qualified service person. 

DO NOT 

strike or slam the

glass door.

The glass door assembly 

SHALL ONLY 

be replaced

as a complete unit, as supplied by the gas fireplace
manufacturer.

NO SUBSTITUTE 

material may be

used.

DO NOT USE 

abrasive cleaners on the glass door

assembly.

DO NOT ATTEMPT 

to clean the glass

door when it is hot.

Turn off the gas before servicing this appliance. It is
recommended that a qualified service technician
perform an appliance check-up at the beginning of
each heating season.

Any safety screen or guard removed for servicing
must be replaced before operating this appliance.

DO NOT 

place furniture or any other combustible

household objects within 36 inches of the fireplace
front.

READ

and

UNDERSTAND

all instructions carefully

before starting the installation. 

FAILURE TO

FOLLOW

these installation instructions may result in

a possible fire hazard and will void the warranty.

Prior to the first firing of the fireplace, 

READ

the

Using Your Fireplace section of the 

Owners Guide

.

DO NOT USE 

this appliance if any part has been

under water. Immediately 

CALL

a qualified service

technician to inspect the unit and to replace any part
of the control system and any gas control which has
been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be 

PERFORMED

by a

qualified service person. The appliance and venting
system should be 

INSPECTED

before initial use and

at least annually by a professional service person.
More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc.
It is 

IMPERATIVE

that the unit’s control

compartment, burners, and circulating air
passageways

BE KEPT CLEAN 

to provide for

adequate combustion and ventilation air.

Always

KEEP

the appliance clear and free from

combustible materials, gasoline, and other
flammable vapors and liquids.

NEVER OBSTRUCT 

the flow of combustion and

ventilation air. Keep the front of the appliance

CLEAR

of all obstacles and materials for servicing

and proper operations.

Due to the high temperature, the appliance should
be

LOCATED

out of traffic areas and away from

furniture and draperies. Clothing or flammable
material

SHOULD NOT BE PLACED 

on or near the

appliance.

Children and adults should be 

ALERTED

to the

hazards of high surface temperature and should

STAY AWAY 

to avoid burns or clothing ignition.

Young children should be 

CAREFULLY

SUPERVISED

when they are in the same room as

the appliance.

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

SAFETY AND WARNING INFORMATION

!

!

Содержание QV32






































Отзывы: