Viking Access Systems I-770 Скачать руководство пользователя

Страница: 41 / 52

VIKING TECHNICAL SUPPORT 1.800.908.0884

3 9

TROUBLESHOOTING

LCD Display References

LCD MSG

Meaning

Page 41

TS Ref #s

RED CONN
UNPLUGED

The Motor Connector is not plugged into the red Open Left or Open Right
socket at the control board. (pg 3, 22)

Multi Meter Displays

MOT AMP
__._ A

This is the motor current amperage during operation.

MOT VOLT
__._ VDC

This is the actual motor voltage during operation.

AC VOLT
__._ VAC

This is the actual low voltage AC to the Control Board from the
transformer.

CHARGE
__._ VDC

Indicates the charging voltage to the batteries, if the Battery Switch is in
the OFF position.

BAT VOLT
__._ VDC

Indicates battery voltage, if the AC power is discontinued to the Control
Board.

Board Settings Messages

Speed
__

Shows the percentage of speed set by the Speed adjustment on the control
board. (pg 25)

OVERLAP
_._ SEC

Shows the number of seconds set by the Overlap Adjustment on the
control board.

ODS SENS
___

Shows the force setting selected to trip the obstruction sensor. (pg 25, 27)

TIMER
__ SEC

Shows the amount time set or remaining to hold the gate at the Open Limit
position, before the gate starts to close. (pg 25)

HEATER
CLS OFF

The Integrated Heater has been disabled for the Closed Limit. (pg 28)

HEATER
CLS ON

The Integrated Heater has been enabled to turn on at the Close Limit

position (pg 28)

“ACTIVE”

will be displayed while it is heating.

HEATER
OPN OFF

The integrated Heater has been disabled for the Open Limit. (pg 28)

HEATER
OPN ON

The Integrated Heater has been enabled to turn on at the Open Limit

position (pg 28)

“ACTIVE”

will be displayed while it is heating.

SOLAR
MODE OFF

The Solar Mode feature is turned OFF. (pg 21, 45)

SOLAR
MODE ON

The Solar Mode feature is turned ON. (pg 21, 45)

Содержание I-770





















































Результаты поиска

Содержание I-770

Отзывы:

Похожие инструкции для I-770

Бренды по названию

Популярные бренды

Viking Access Systems I-770, Инструкции по установке и информация о безопасности

Результаты поиска

Содержание I-770

Отзывы:

Похожие инструкции для I-770

Бренды по названию

Популярные бренды