Viking Access Systems I-770 Скачать руководство пользователя

Страница: 42 / 52

VIKING TECHNICAL SUPPORT 1.800.908.0884

4 0

TROUBLESHOOTING

LCD Display References

LCD MSG

Meaning

Page 41

TS Ref #s

Error Messages

ERR AC
LOW

Indicates that the 24VAC supply to the VFlex Board is too low from the
115/230 power supply.

1, 3, 20

ERR AC
HIGH

Indicates that the 24VAC supply to the VFlex Board is too high from the
115/230 power supply.

1, 3, 20

ERR AC
NO AC

Indicates that there is no 24VAC supply detected to the VFlex Board from
the 115/230 power supply.

1, 2, 4,
20

ERR CHRG
HIGH

Potential problem with the charging voltage from the control board.

1, ?

ERR CHRG
CHECK 4A

a) 4 Amp Fuse is blown, or;
b) There is a problem with the batteries or the control board.

18, ?

ERR BAT
LOW

The battery is low.

1, 2, 3,
4

ERR FUSE
15 AMP

15 Amp motor fuse is blown on the Primary or Single Control Board.

7, 11, 12

ERR EMI
NO EMI

No EMI board detected.

ERR EMI
NO FUSE

4 Amp main fuse is blown on Power Supply Panel Assembly.

ERR EMI
NO AC

There is no AC voltage detected from the EMI Board.

ERR EMI
Unknown

There is a problem with the communication between the EMI Board and the
VFlex Board.

ERR EMI
PROTECT

Lightning strike protection for the EMI Board (behind the Control Board
assembly) needs to be replaced.

ERR FUSE
15A S

15 Amp motor fuse is blown on the Secondary Module.

7, 11, 12

ERR REFV
WRONG

One, or more, of the internal reference voltages from the VFlex (Primary)
Control Board are incorrect.

ERR SENS
UL RO

There is a problem with the required monitored sensor(s) connected
to the “UL” and/or “Re-Open” input terminals (pg 10-11, 29).

ERRLIMIT
OPN+CLS

There is a problem with the Limit Switches or Wires.

6, 24

Содержание I-770





















































Результаты поиска

Содержание I-770

Отзывы:

Похожие инструкции для I-770

Бренды по названию

Популярные бренды

Viking Access Systems I-770, Инструкции по установке и информация о безопасности

Результаты поиска

Содержание I-770

Отзывы:

Похожие инструкции для I-770

Бренды по названию

Популярные бренды