Viking Access Systems I-770 Скачать руководство пользователя страница 25

Страница: 25 / 52

VIKING TECHNICAL SUPPORT 1.800.908.0884

2 3

Motor Cable - Secondary (Dual)

NOTE:

The Primary/Secondary, or Dual, Electronic Control Unit is equipped with both

the VFlex Control Board (Primary) and a Secondary Module, both are required to
operate two gate motors in tandem.

STEP 6

Secondary Motor:

a. Connect the BROWN and BLUE

wires from the motor cable to the
terminal block at the Secondary
Module Board.

b. Attach the grounding wire (non

insulated) to the Board Mounting
Plate using the screw provided.

ELECTRICAL INSTALLATION

STEP 5

Secondary to Primary Connections:

a. Ensure that the Secondary

Power Harness is connected as
illustrated. Polarity is important!

Red to “

”

Black to “

–

”

b. Ensure that the Primary/

Secondary Communication Cable
is connected as illustrated.

Secondary Motor

BROWN

BLUE

NOT USED

Primary Motor

BROWN
BLUE

JUMPER

NOT USED

STEP 7

Secondary Open Left or Open Right:

Refer to the illustration on page 22.

Place the terminal block in the proper location for the gate opening direction.

• “OPEN RIGHT” Connector if the gate opens

Inside to the Right

Outside to the Left

• “OPEN LEFT” Connector if the gate opens

Inside to the Left

Outside to the Right

I-770

Содержание I-770





















































Результаты поиска

Содержание I-770

Отзывы:

Похожие инструкции для I-770

Бренды по названию

Популярные бренды

Viking Access Systems I-770, Инструкции по установке и информация о безопасности

Результаты поиска

Содержание I-770

Отзывы:

Похожие инструкции для I-770

Бренды по названию

Популярные бренды