Videx IP videokit IPVK-1/6296 Скачать руководство пользователя страница 8

Страница: 8 / 60

66550062-EN - V 1.1 - 31/05/18

- 8 -

IPVK/6296 Series IP videokit

IPVK/6296 Series - Installation handbook

ENABLE BOOTLOADER MODE

In case of firmware update failure (i.e. because of mains failure or

cable disconnection during the update etc.) and the door panel is

not anymore recognized by the Videx IP Wizard software, you can

try to restore it by manually putting it into boot mode.

It is strongly recommended that this operation is carried out by

a qualified engineer and in any case after a contact with videx

support.

• Disconnect the door panel from the power supply.

• Press and keep pressed the “

” button (Fig. 2 on page 5) then

connect again the power supply source.

• The door panel goes in boot mode recognized by the four

LEDs flashing alternatively (Fig. 11).

• Now proceed using the utility “VidexFirmwareUpdater.exe” to

upload the firmware to the device.

• If the update process terminates correctly, the device should

be restored and ready to work.

• If the device still not work, please contact the supplier to proceed according to the warranty terms.

TECHNICAL SPECIFICATION

SIGNALS ON SYSTEM CONNECTION TERMINALS

EXT

CAMERA

Active low output enabled when the

external video input is in use

GND

Composite video signal ground reference

Composite video signal input

RS485

RS-485 Connection (termination adjusted

through the JP1 jumper)

GND

POWER

+12V

12Vdc 400mA power supply input

GND

INPUTS

PTE1

Active low input 1 (when enabled activate

the relay 1)

PTE2

Active low input 2 (when enabled activate

the relay 1)

GNDP

Ground reference to be used with PTE inputs

ETHERNET

RX–

Ethernet Connection Orange (568A)

RX+

Ethernet Connection White/Orange (568A)

TX–

Ethernet Connection Green (568A)

TX+

Ethernet Connection White/Green (568A)

RELAY 2

Relay 2 common contact

Max

12-24

Vac/dc

0.4A

NC2

Relay 2 normally closed contact

NO2

Relay 2 normally open contact

RELAY 1

Relay 1 common contact

NC1

Relay 1 normally closed contact

NO1

Relay 1 normally open contact

UNIT SPECIFICATION
Housing/Mounting:

One 4000 Series Module / 4000 Series

Modular System

Push Buttons:

Yes, from 0 to 2 call buttons depend-

ing on the model

Programming:

Yes, carried out by the 8 way dip-switch

located on the rear of the module

Controls:

Microphone and Loudspeaker volume

trimmers

Front plate finishes:

Mirror stainless steel (standard),

Anodized Aluminium (add /a after the

product code) or High Brass (add /HB)

Power Supply:

12Vdc - 400mA

Power consumption:

Stand-by:

Operating:

Working Temperature:

-10 +50 °C

Fig. 11

Door panel in BOOTLOADER mode

Art. 4533

IP speaker unit module

Содержание IP videokit IPVK-1/6296





























































Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды

Videx IP videokit IPVK-1/6296, Руководство по установке

Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды