Videx IP videokit IPVK-1/6296 Скачать руководство пользователя страница 6

Страница: 6 / 60

66550062-EN - V 1.1 - 31/05/18

- 6 -

IPVK/6296 Series IP videokit

IPVK/6296 Series - Installation handbook

Art. 4533

IP speaker unit module

FRONT LEDS SIGNALLING DESCRIPTION

Flashes when the called indoor station is busy is busy. The LED will be off when the system is in stand-by,

If illuminated, indicates that the call from the outdoor station is in progress. The LED will switch OFF when the call

is answered or expired the call time without any answer.

If illuminated, indicates that it is possible to speak because the call has been answered. The LED will switch OFF at

the end of a conversation (or at the end of the conversation time).

If illuminated, indicates that the door lock has been operated. It will switch OFF at the end of the programmed

“door opening” time.

PROGRAMMING

The programming of the module is carried out through the VIDEX IP Wizard software.

Directly on the module are allowed some adjustments:

• Microphone volume through the relevant trimmer;

• Loudspeaker volume through the relevant trimmer;

• RS-485 connection termination.

For the module programming refer to the section VIDEX IP Wizard.

GENERAL DIRECTIONS FOR MODULE INSTALLATION

MAXIMUM ILLUMINATION DISTANCE FROM CAMERA AT NIGHT

The IR LED’s within the camera will illuminate the visitor when they are within 50 cm of the camera.

MAX 50 cm

ADHESIVE GASKET PLACEMENT

Apply the

seal as shown in Fig. 3.

ANTI-TAMPERING LOCKS FIXING

Fit the anti-tampering locks

as shown in Fig. 4.

Fig. 3

Fig. 4

HOW TO REMOVE/INSERT THE CARD NAME HOLDER

• To avoid damage to the module front plate, mask the side that

will be in contact with the screwdriver blade;

• Insert the screwdriver (flat side) into the card-holder hole as

shown in

Fig. 5

;

• Move the screwdriver to the left as shown in

Fig. 6

to extract

the card name holder;

• Edit the card name then replace it inside the holder and refit:

insert the holder inside its housing from the left or right side

then push the other side until it clips into place.

Fig. 5

Fig. 6

Содержание IP videokit IPVK-1/6296





























































Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды

Videx IP videokit IPVK-1/6296, Руководство по установке

Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды