Videx IP videokit IPVK-1/6296 Скачать руководство пользователя страница 30

Страница: 30 / 60

66550062-EN - V 1.1 - 31/05/18

- 30 -

IPVK/6296 Series IP videokit

IPVK/6296 Series - Installation handbook

ENABLE BOOTLOADER MODE

In case of firmware update failure (i.e. because of mains failure or

cable disconnection during the update etc.) and the videophone

is not anymore recognized by the Videx IP Wizard software, you

can try to restore it by manually putting it into boot mode.

It is strongly recommended that this operation is carried out by

a qualified engineer and in any case after a contact with videx

support.

• Disconnect the videophone from power supply (ethernet

connector if supplied by POE or +12Vdc terminal connector

if supplied by a power supply unit).

• Press and keep pressed

button then connect again the

power supply source (ethernet connector if supplied by POE or

+12Vdc terminal connector if supplied by a power supply unit).

• The videophone goes in boot mode recognized by the four

LEDs flashing alternatively (Fig. 65).

• Now proceed using the utility “VidexFirmwareUpdater.exe”

to upload the firmware to the device.

• If the update process terminates correctly, the device should be restored and ready to work.

• If the device still not work, please contact the supplier to proceed according to the warranty terms.

TECHNICAL SPECIFICATIONS

SIGNALS ON CONNECTION TERMINALS

GNDP

Ground for PTE inputs

PTE2

Active low input 2 (to implement)

PTE1

Active low input 1 (to implement)

OUT2

Relay 2 - C & NO dry contacts (to implement)

OUT2
OUT1

Relay 1 - C & NO dry contacts (to implement)

OUT1

+12

12 Vdc power supply input. This is not used if

the videophone is connected to a POE Switch or

Router

GND

RS-485 connection

GND

SPECIFICATION
Housing/Mounting:

6200 Series Videophones

Surface mount

Push buttons:

Yes, 4

Programming:

Yes, carried out by the buttons and

the PC.

Controls:

Call tone volume, brightness

Power Supply:

12Vdc or POE

Power consumption:

Stand-by: 0.2mA

Operating: 115mA

Working Temperature:

-10 +50 °C

Fig. 65

Monitor in boot mode

Art. 6296

IP Videophone for VIDEX IP System

Содержание IP videokit IPVK-1/6296





























































Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды

Videx IP videokit IPVK-1/6296, Руководство по установке

Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды