Videx IP videokit IPVK-1/6296 Скачать руководство пользователя страница 5

Страница: 5 / 60

66550062-EN - V 1.1 - 31/05/18

- 5 -

IPVK/6296 Series IP videokit

IPVK/6296 Series - Installation handbook

Art. 4533

IP speaker unit module for VIDEX IP System

Fig. 1

STEEL

ALI

HIGH BRASS

4533-0

4533-1

4533-2

Made in Italy

RELAY 1 RELAY 2

INPUTS

EXT CAMERA

POWER

ETHERNET

EXPANSION

BUTTONS

RS485

NO1 NC1

NO2 NC2

PTE1

GNDP PTE2

GND +12V

RX+ RX–

TX+ TX–

GND B A

JP1

GND SL

Close

Open

RESET?

TIA/EIA-568-A.1-2001 T56AB

Wiring

Orange

Orange-white

Green

White-green

White-Green

Green

White-Orange

Blue

White-Blue

Orange

White-brown

Brown

Fig. 2

DESCRIPTION

IP speaker unit module with built-in wide colour day/night camera with autoiris lens and IR illumination LEDs. Depending on the

speaker unit version it includes one or two call push buttons. The unit circuitry incorporates:

• The transmitting amplifier with microphone and volume control;

• The receiving amplifier with volume control;

• Two enslavement relay to enable electric locn and an additional service (3 contacts each: common, normally open and normally closed).

• The call buttons from 1 to a maximum of 2 depending on the module version;

• The illumination LEDs for the card name holder;

• The camera comprised of illumination LEDs.

MODULE DETAILS:

Camera with illumination LEDs;

Operation LEDs;

Loudspeaker;

Card name holder;

Call push button (0, 1 or 2 depending on the model);

Microphone;

Loudspeaker volume control;

Microphone volume control;

RS485 connection terminals;

Boot loader push button for firmware update;

RS485 termination jumper;

External camera connection terminals;

System connection terminals;

Button expansion modules connector

AVAILABLE MODULE VERSIONS

Art. 4533-0

Art. 4533-1

Art. 4533-2

Содержание IP videokit IPVK-1/6296





























































Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды

Videx IP videokit IPVK-1/6296, Руководство по установке

Результаты поиска

Содержание IP videokit IPVK-1/6296

Отзывы:

Похожие инструкции для IP videokit IPVK-1/6296

Бренды по названию

Популярные бренды